DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P-Seatbelt Buckle SW | Front seat belt buckle switch (Passenger Side)*1 | OFF or ON | OFF: Front passenger seat belt fastened
ON: Front passenger seat belt unfastened |
The front passenger seat is occupied |
| 2nd-Row Seatbelt Buckle (R) | Rear seat belt buckle switch RH*2 | OFF or ON | OFF: Rear RH seat belt fastened
ON: Rear RH seat belt unfastened |
- |
| 2nd-Row Seatbelt Buckle (L) | Rear seat belt buckle switch LH*2 | OFF or ON | OFF: Rear LH seat belt fastened
ON: Rear LH seat belt unfastened |
- |
| 2nd-Row Seatbelt Buckle (C) | Rear seat center belt buckle switch*2 | OFF or ON | OFF: Rear seat center belt fastened
ON: Rear seat center belt unfastened |
- |
| Driver Side Seatbelt Buckle Switch | Front seat belt buckle switch (Driver Side) | OFF or ON | OFF: Driver seat belt fastened
ON: Driver seat belt unfastened |
- |
| Driver Side Door | Driver side door courtesy light switch LH signal | OFF or ON | ON: Driver side door opened
OFF: Driver side door closed |
- |
| Passenger Side Door | Front passenger side door courtesy light switch LH signal | OFF or ON | ON: Front passenger side opened
OFF: Front passenger side closed |
- |
| Rear Left Side Door | Rear door courtesy light switch LH signal | OFF or ON | ON: Rear door LH opened
OFF: Rear door LH closed |
- |
| Rear Right Side Door | Rear door courtesy light switch RH signal | OFF or ON | ON: Rear door RH opened
OFF: Rear door RH closed |
- |
| Driver Side Seatbelt Warning Buzzer | Driver side seat belt warning buzzer | OFF or ON | Customized value displayed | - |
| P-Seatbelt Warning Buzzer | Front passenger side seat belt warning buzzer*1 | OFF or ON | Customized value displayed | - |
| Rear Seatbelt Warning Buzzer | Rear seat belt warning buzzer*2 | OFF or ON | Customized value displayed | - |
*1: w/ Front Passenger Seat Belt Warning System
*2: w/ Rear Seat Belt Warning System
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Front seat belt warning light | OFF or ON | Confirm that the vehicle is stopped with the engine idling |
| Rear Seat Belt | Rear seat belt warning light*1 | OFF or ON | Confirm that the vehicle is stopped with the engine idling |
*1: w/ Rear Seat Belt Warning System