Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2017.10
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0084737 SEAT BELT WARNING SYSTEM G

SEAT BELT  SEAT BELT WARNING SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVER SIDE SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the ignition switch to ON.


b.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


c.

Lift up the vehicle using a swing arm type lift.


d.

Start the engine.


e.

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


f.

When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.


Hide 2.INSPECT FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT (w/ Front Passenger Seat Belt Warning System)

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the ignition switch to ON.


b.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



c.

Fasten the driver seat belt.


d.

When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


e.

Lift up the vehicle using a swing arm type lift.

Click here


f.

Start the engine.


g.

When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


h.

When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.


Hide 3.INSPECT REAR SEAT BELT WARNING LIGHT ((w/ Rear Seat Belt Warning))

a.

Check the state of the rear seat belt warning light on the heater control and accesory assembly*1 or air conditioning control assembly*2 under the following conditions:

i.

Turn the ignition switch to ON.


ii.

When a rear seat belt is not fastened, check that the rear seat belt warning light on the heater control and accesory assembly*1 or air conditioning control assembly*2 illuminated.


iii.

After 34 seconds, check that the rear seat belt warning light on the heater control and accesory assembly*1 or air conditioning control assembly*2 is turns off.


iv.

When one of the rear seat belts is unfastened from fastened, check that the rear seat belt warning light on the heater control and accesory assembly*1 or air conditioning control assembly*2 illuminates.

*1: for Manual Air Conditioning System

*2: for Automatic Air Conditioning System




Hide 4.INSPECT SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


a.

Place a weight of 20 kg (44.0 lb) on the front passenger seat. *1

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



b.

Lift up the vehicle using a swing arm type lift.


c.

Start the engine.


d.

Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver or front passenger seat belt is not fastened.


e.

Check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds.


f.

After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.


g.

Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.


h.

After the buzzer has stopped, turn the ignition switch off and then start the engine again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver or front passenger seat belt is not fastened, and check that the buzzer sounds again.


i.

After the buzzer has stopped, stop the vehicle, move the shift lever to R, and then move it to D.Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.

*1: w/ Front Passenger Seat Belt Warning System