Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0086434 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for TMMIN Made)


a.
B108710E06
1.469,0.302 1.854,0.552 0.385,0.25 1.573,0.354 1.885,0.552 0.313,0.198 10 false H8

Disconnect the power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H8-6 (B) - H8-1 (E) V - W-B Power supply Ignition switch ON 11 to 14 V
H8-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the power window regulator master switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H8-8 (U) - H8-1 (E) R - W-B Power window motor UP operation Ignition switch ON, driver side door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
H8-5 (D) - H8-1 (E) SB - W-B Power window motor DOWN operation Ignition switch ON, driver side door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
H8-4 (AUTO) - H8-1 (E) BR - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
H8-3 (LED+) - H8-1 (E) P - W-B LED illumination signal Ignition switch ON 11 to 14 V
Ignition switch turned off Below 1 V

If the result is not as specified, the power window regulator master switch assembly may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (for TMMIN Made)


a.
C281434E07
1.5,0.25 1.906,0.5 0.406,0.25 1.625,0.292 1.865,0.448 0.24,0.156 10 false G8

Disconnect the power window regulator switch assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G8-3 (B) - Body ground B - Body ground Power supply Ignition switch ON 11 to 14 V
G8-5 (SU) - Body ground P - Body ground Ground Always Below 1 Ω
G8-2 (SD) - Body ground R - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the power window regulator switch assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G8-4 (U) - Body ground LA-R - Body ground Power window motor UP operation Power window regulator switch assembly RH OFF → UP Below 1 V → 11 to 14 V
G8-1 (D) - Body ground LA-SB - Body ground Power window motor DOWN operation Power window regulator switch assembly RH OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly RH may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (for TMMIN Made)


C281434E02
1.5,0.25 1.917,0.5 0.417,0.25 1.646,0.292 1.875,0.469 0.229,0.177 10 false J1

a.

Disconnect the rear power window regulator switch assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-3 (B) - Body ground LA-P - Body ground Power supply Ignition switch ON 11 to 14 V
J1-5 (SU) - Body ground LA-BE - Body ground Ground Always Below 1 Ω
J1-2 (SD) - Body ground LA-G - Body ground Ground Always Below 1 Ω


c.

Reconnect the rear power window regulator switch assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-4 (U) - Body ground R - Body ground Power window motor UP operation Rear power window regulator switch assembly LH OFF → UP Below 1 V → 11 to 14 V
J1-1 (D) - Body ground SB - Body ground Power window motor DOWN operation Rear power window regulator switch assembly LH OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the rear power window regulator switch assembly LH may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (for TMMIN Made)


C281434E04
1.5,0.25 1.917,0.5 0.417,0.25 1.656,0.292 1.854,0.469 0.198,0.177 10 false I1

a.

Disconnect the rear power window regulator switch assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I1-3 (B) - Body ground LA-P - Body ground Power supply Ignition switch ON 11 to 14 V
I1-5 (SU) - Body ground LA-GR - Body ground Ground Always Below 1 Ω
I1-2 (SD) - Body ground LA-L - Body ground Ground Always Below 1 Ω


c.

Reconnect the rear power window regulator switch assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I1-4 (U) - Body ground R - Body ground Power window motor UP operation Rear power window regulator switch assembly RH OFF → UP Below 1 V → 11 to 14 V
I1-1 (D) - Body ground SB - Body ground Power window motor DOWN operation Rear power window regulator switch assembly RH OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the rear power window regulator switch assembly RH may have a malfunction.



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for TMMIN Made)


a.
B264165N04
0.521,0.906 0.927,1.135 0.406,0.229 0.635,0.938 0.948,1.135 0.313,0.198 10 false H7

Disconnect the front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
H7-2 (B) - H7-1 (GND) GR - W-B Power supply Always 11 to 14 V
H7-6 (IG) - H7-1 (GND) G - W-B IG signal Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H7-10 (UP) - H7-1 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver side door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
H7-7 (DOWN) - H7-1 (GND) SB - W-B Power window motor DOWN operation Ignition switch ON, driver side door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
H7-4 (AUTO) - H7-1 (GND) BR - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
H7-5 (LED) - H7-1 (GND) P - W-B LED illumination signal Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

If the result is not as specified, the front power window regulator motor assembly LH may have a malfunction.



CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for TMT Made)


a.

for LHD

i.
B108710E06
1.469,0.302 1.854,0.552 0.385,0.25 1.573,0.354 1.885,0.552 0.313,0.198 10 false H8

Disconnect the power window regulator master switch assembly connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H8-7 (B) - H8-1 (E) V - W-B Power supply Ignition switch ON 11 to 14 V
H8-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the power window regulator master switch assembly connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H8-6 (U) - H8-1 (E) R - W-B Power window motor UP operation Ignition switch ON, driver side door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
H8-3 (D) - H8-1 (E) SB - W-B Power window motor DOWN operation Ignition switch ON, driver side door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
H8-4 (A) - H8-1 (E) BR - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
H8-15 (ILL+) - H8-5 (ILL-) B - W-B LED illumination signal Ignition switch ON 11 to 14 V
Ignition switch turned off Below 1 V

If the result is not as specified, the power window regulator master switch assembly may have a malfunction.



b.

for RHD

i.
B108710E04
1.469,0.302 1.854,0.552 0.385,0.25 1.573,0.354 1.885,0.552 0.313,0.198 10 false G5

Disconnect the power window regulator master switch assembly connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G5-7 (B) - G5-9 (E) V - W-B Power supply Ignition switch ON 11 to 14 V
G5-9 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the power window regulator master switch assembly connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G5-3 (U) - G5-9 (E) R - W-B Power window motor UP operation Ignition switch ON, driver side door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
G5-6 (D) - G5-9 (E) SB - W-B Power window motor DOWN operation Ignition switch ON, driver side door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
G5-4 (A) - G5-9 (E) BR - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V
G5-17 (ILL+) - G5-5(ILL-) B - W-B LED illumination signal Ignition switch ON 11 to 14 V
Ignition switch turned off Below 1 V

If the result is not as specified, the power window regulator master switch assembly may have a malfunction.




CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH (for TMT Made)


a.

for LHD

i.
B402537E13
1.479,0.292 1.979,0.542 0.5,0.25 1.604,0.333 1.917,0.531 0.313,0.198 10 false G10

Disconnect the power window regulator switch assembly RH connector.


ii.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G10-2 (B) - Body ground B - Body ground Power supply Ignition switch ON 11 to 14 V
G10-3 (SU) - Body ground P - Body ground Ground Always Below 1 Ω
G10-4 (SD) - Body ground R - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.



b.

Reconnect the power window regulator switch assembly RH connector.


c.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G10-7 (U) - Body ground LA-R - Body ground Power window motor UP operation Power window regulator switch assembly RH OFF → UP Below 1 V → 11 to 14 V
G10-1 (D) - Body ground LA-SB - Body ground Power window motor DOWN operation Power window regulator switch assembly RH OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly RH may have a malfunction.


d.

for RHD

i.
B402537E17
1.479,0.292 1.979,0.542 0.5,0.25 1.625,0.344 1.938,0.542 0.313,0.198 10 false H10

Disconnect the power window regulator switch assembly LH connector.


ii.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H10-2 (B) - Body ground L - Body ground Power supply Ignition switch ON 11 to 14 V
H10-3 (SU) - Body ground LG - Body ground Ground Always Below 1 Ω
H10-4 (SD) - Body ground P - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.



e.

Reconnect the power window regulator switch assembly LH connector.


f.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H10-7 (U) - Body ground LA-R - Body ground Power window motor UP operation Power window regulator switch assembly LH OFF → UP Below 1 V → 11 to 14 V
H10-1 (D) - Body ground LA-SB - Body ground Power window motor DOWN operation Power window regulator switch assembly LH OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly LH may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (for TMT Made)


B402537E14
1.479,0.292 1.979,0.542 0.5,0.25 1.646,0.333 1.958,0.531 0.313,0.198 10 false J5

a.

Disconnect the rear power window regulator switch assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J5-2 (B) - Body ground LA-B - Body ground Power supply Ignition switch ON 11 to 14 V
J5-3 (SU) - Body ground LA-BE - Body ground Ground Always Below 1 Ω
J5-4 (SD) - Body ground LA-G - Body ground Ground Always Below 1 Ω


c.

Reconnect the rear power window regulator switch assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J5-7 (U) - Body ground R - Body ground Power window motor UP operation Rear power window regulator switch assembly LH OFF → UP Below 1 V → 11 to 14 V
J5-1 (D) - Body ground SB - Body ground Power window motor DOWN operation Rear power window regulator switch assembly LH OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the rear power window regulator switch assembly LH may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (for TMT Made)


B402537E12
1.479,0.292 1.979,0.542 0.5,0.25 1.646,0.354 1.958,0.552 0.313,0.198 10 false I5

a.

Disconnect the rear power window regulator switch assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I5-2 (B) - Body ground LA-P - Body ground Power supply Ignition switch ON 11 to 14 V
I5-3 (SU) - Body ground LA-GR - Body ground Ground Always Below 1 Ω
I5-4 (SD) - Body ground LA-L - Body ground Ground Always Below 1 Ω


c.

Reconnect the rear power window regulator switch assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I5-7 (U) - Body ground R - Body ground Power window motor UP operation Rear power window regulator switch assembly RH OFF → UP Below 1 V → 11 to 14 V
I5-1 (D) - Body ground SB - Body ground Power window motor DOWN operation Rear power window regulator switch assembly RH OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the rear power window regulator switch assembly RH may have a malfunction.



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH (for TMT Made)


a.

for LHD

i.
B264165E05
0.521,0.906 0.927,1.135 0.406,0.229 0.604,0.938 0.948,1.146 0.344,0.208 10 false H11

Disconnect the front power window regulator motor assembly LH connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H11-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
H11-2 (B) - H11-1 (GND) GR - W-B Power supply Always 11 to 14 V
H11-6 (IG) - H11-1 (GND) R - W-B IG signal Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the front power window regulator motor assembly LH connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H11-10 (UP) - H11-1 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver side door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
H11-7 (DOWN) - H11-1 (GND) SB - W-B Power window motor DOWN operation Ignition switch ON, driver side door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
H11-4 (AUTO) - H11-1 (GND) BR - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the front power window regulator motor assembly LH may have a malfunction.



b.

for RHD

i.
B264165E06
0.521,0.906 0.927,1.135 0.406,0.229 0.604,0.938 0.948,1.167 0.344,0.229 10 false G11

Disconnect the front power window regulator motor assembly RH connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G11-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
G11-2 (B) - G11-1 (GND) GR - W-B Power supply Always 11 to 14 V
G11-6 (IG) - G11-1 (GND) R - W-B IG signal Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


iii.

Reconnect the front power window regulator motor assembly RH connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G11-10 (UP) - G11-1 (GND) R - W-B Power window motor UP operation Ignition switch ON, driver side door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
G11-7 (DOWN) - G11-1 (GND) SB - W-B Power window motor DOWN operation Ignition switch ON, driver side door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
G11-4 (AUTO) - G11-1 (GND) BR - W-B Power window motor AUTO operation Ignition switch ON, driver side door glass fully opened → driver side power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened 11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the front power window regulator motor assembly RH may have a malfunction.