Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0086434 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Power Windows do not Operate at All  


DESCRIPTION

If all of the power windows do not operate, the power window regulator master switch assembly may have no power or may be malfunctioning.

WIRING DIAGRAM

E263565E14
4.542,0.448 4.698,0.646 0.156,0.198 10 false 6 4.542,1.281 4.698,1.479 0.156,0.198 10 false 1 4.729,0.552 4.885,0.75 0.156,0.198 10 false B 4.719,1.406 4.875,1.604 0.156,0.198 10 false E 4.906,1.813 5.167,2 0.26,0.188 10 false H8 3.167,0.708 3.802,0.906 0.635,0.198 10 false POWER 0.854,0.552 2.156,0.833 1.302,0.281 10 false from POWER Relay 4.906,1.958 6.521,2.396 1.615,0.438 10 false Power Window Regulator Master Switch Assembly 0.052,0.031 1.521,0.271 1.469,0.24 12 false for TMMIN Made:

E263565E15
4.542,0.448 4.698,0.646 0.156,0.198 10 false 7 4.542,1.281 4.698,1.479 0.156,0.198 10 false 1 4.729,0.552 4.885,0.75 0.156,0.198 10 false B 4.719,1.406 4.875,1.604 0.156,0.198 10 false E 4.906,1.813 5.167,2 0.26,0.188 10 false H8 3.167,0.708 3.802,0.906 0.635,0.198 10 false POWER 0.854,0.552 2.156,0.833 1.302,0.281 10 false from POWER Relay 4.906,1.958 6.521,2.396 1.615,0.438 10 false Power Window Regulator Master Switch Assembly 0.073,0.063 1.719,0.344 1.646,0.281 12 false for TMT Made LHD:

E263565E16
4.542,0.448 4.698,0.646 0.156,0.198 10 false 7 4.542,1.281 4.698,1.479 0.156,0.198 10 false 9 4.729,0.552 4.885,0.75 0.156,0.198 10 false B 4.719,1.406 4.875,1.604 0.156,0.198 10 false E 4.906,1.813 5.167,2 0.26,0.188 10 false G5 3.167,0.708 3.802,0.906 0.635,0.198 10 false POWER 0.854,0.552 2.156,0.833 1.302,0.281 10 false from POWER Relay 4.906,1.958 6.521,2.396 1.615,0.438 10 false Power Window Regulator Master Switch Assembly 0.073,0.063 1.802,0.354 1.729,0.292 12 false for TMT Made RHD:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMMIN Made A
for TMT Made B



A

2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY GROUND)
a.
B276330C42
0.135,0.875 0.667,1.167 0.531,0.292 1.031,1.021 1.406,0.354 true 0.313,0.948 0.573,1.115 0.26,0.167 10 false H8 0.083,0 0.281,0.188 0.198,0.188 10 false *a 1.469,0.24 1.615,0.427 0.146,0.188 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Disconnect the power window regulator master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY GROUND)
a.

for LHD

i.
B276330C42
0.135,0.875 0.667,1.167 0.531,0.292 1.031,1.021 1.406,0.354 true 0.313,0.948 0.573,1.115 0.26,0.167 10 false H8 0.083,0 0.281,0.188 0.198,0.188 10 false *a 1.469,0.24 1.615,0.427 0.146,0.188 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Disconnect the power window regulator master switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-1 (E) - Body ground Always Below 1 Ω




b.

for RHD

i.
B276330C52
0.135,0.875 0.667,1.167 0.531,0.292 2.469,1.031 2.938,0.625 true 0.313,0.948 0.573,1.115 0.26,0.167 10 false G5 0.083,0 0.281,0.188 0.198,0.188 10 false *a 2.979,0.552 3.125,0.74 0.146,0.188 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Disconnect the power window regulator master switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-9 (E) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR