CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)
Disconnect the F3 air conditioning amplifier assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F3-1 (IG+) - F3-14 (GND) | G - W-B*1
R - W-B*2 |
Power source (IG) | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| F3-21 (B) - F3-14 (GND) | GR - W-B | Battery power supply | Always | 11 to 14 V |
| F3-14 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
*1: for TMMIN Made
*2: for TMT Made
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F3 air conditioning amplifier assembly connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F3-38 (RDFG) - F3-14 (GND) | SB - W-B | Rear window defogger signal | Ignition switch ON, rear window defogger switch off | 11 to 14 V |
| Ignition switch ON, rear window defogger switch on | Below 1 V | |||
| F3-4 (LIN1) - F3-14 (GND) | BE - W-B | LIN communication line | Ignition switch ON | Pulse generation |
If the result is not as specified, the air conditioning amplifier assembly may be malfunctioning.
CHECK AIR CONDITIONING CONTROL ASSEMBLY (for TMMIN Made with Automatic Air Conditioning System)
Disconnect the F4 air conditioning control assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F4-8 (IG+) - F4-5 (GND) | G - W-B | Power source (IG) | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| F4-5 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F4 air conditioning control assembly connector.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F4-2 (LIN1) - F4-5 (GND) | BE - W-B | LIN communication line | Ignition switch ON | Pulse generation |
If the result is not as specified, the air conditioning control assembly may be malfunctioning.
CHECK AIR CONDITIONING CONTROL ASSEMBLY (for TMT Made with Automatic Air Conditioning System)
Disconnect the F171 air conditioning control assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F171-1 (IG+) - F171-8 (GND) | G - W-B | Power source (IG) | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| F171-8 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F171 air conditioning control assembly connector.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F171-6 (LIN1) - F171-8 (GND) | BE - W-B | LIN communication line | Ignition switch ON | Pulse generation |
If the result is not as specified, the air conditioning control assembly may be malfunctioning.