CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (for TMMIN Made with Smart Entry and Start System)
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-10 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| F43-1 (+B) - Body ground | V - Body ground | +B power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the certification ECU (smart key ECU assembly) connector.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Switch Condition | Specified Condition |
|---|---|---|---|---|
| F43-5 (LIN) - Body ground | LG - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (for TMT Made with Smart Entry and Start System)
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-10 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| F43-1 (+B) - Body ground | B - Body ground | +B power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the certification ECU (smart key ECU assembly) connector.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Switch Condition | Specified Condition |
|---|---|---|---|---|
| F43-5 (LIN) - Body ground | R - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (w/ Smart Entry and Start System)
Disconnect the steering lock ECU (steering lock actuator assembly) connector.
Measure the resistance and voltage according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F15-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| F15-7 (B) - Body ground | P - Body ground*1
W - Body ground*2 |
Battery power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction on the wire harness side.
*1: for TMMIN Made
*2: for TMT Made
Reconnect the steering lock ECU (steering lock actuator assembly) connector.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Switch Condition | Specified Condition |
|---|---|---|---|---|
| F15-5 (LIN) - Body ground | LG - Body ground*1
R - Body ground*2 |
LIN communication line | Ignition switch ON | Pulse generation |
If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may be malfunctioning.
*1: for TMMIN Made
*2: for TMT Made