84306
1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o Cruise Control System)
Visually check for defects with the spiral cable sub-assembly removed from the vehicle.
The defects are as follows:
Scratches on the spiral cable sub-assembly
Small cracks the spiral cable sub-assembly
Dents on the spiral cable sub-assembly
Chips on the spiral cable sub-assembly
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
| *a | Component without harness connected (Spiral Cable Sub-assembly) |
Check the resistance.
Measure the resistance according to the value(s) in the table below.
To avoid breakage of the spiral cable sub-assembly, do not turn the spiral cable sub-assembly more than necessary.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B1 (HO) - D8 (HO) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| B8 (EAU) - D4 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| B9 (AU2) - D5 (AU2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| B10 (AU1) - D6 (AU1) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| A1 (D-) - E2 (D-) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| A2 (D+) - E1 (D+) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
If the result is not as specified, replace the spiral cable sub-assembly.
84306
2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/ Cruise Control System)
Visually check for defects with the spiral cable sub-assembly removed from the vehicle.
The defects are as follows:
Scratches on the spiral cable sub-assembly
Small cracks the spiral cable sub-assembly
Dents on the spiral cable sub-assembly
Chips on the spiral cable sub-assembly
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
Check the resistance.
Measure the resistance according to the value(s) in the table below.
To avoid breakage of the spiral cable sub-assembly, do not turn the spiral cable sub-assembly more than necessary.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B1 (HO) - D8 (HO) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| B8 (EAU) - D4 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| B9 (AU2) - D5 (AU2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| B10 (AU1) - D6 (AU1) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| A1 (D-) - E2 (D-) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| A2 (D+) - E1 (D+) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| C2 (HO) - D8 (HO) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| C3 (CCS) - D1 (CCS) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| C4 (ECC) - D2 (ECC) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
If the result is not as specified, replace the spiral cable sub-assembly.