Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.
Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to speed signal.
A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.
The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0500 | Vehicle Speed Sensor | While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM.
(1 trip detection logic: for CVT) (2 trip detection logic: for Manual Transaxle) |
·
Open or short in speed signal circuit ·
Combination meter assembly ·
Skid control ECU (Brake actuator assembly) ·
ECM |
Comes on | DTC stored |
The ECM assumes that the vehicle is being driven when the vehicle speed sensor signal is being transmitted by the combination meter. If there is no signal from the combination meter, despite the ECM detecting the speed signal from the speed sensor NOUT, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.
The ECM assumes that the vehicle is being driven when the fuel-cut operation* is being executed. If there is no speed signal, despite the conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.
*: Idle fuel-cut is executed when the throttle valve is fully closed and engine speed is over 2800 rpm.
| Required Sensors/Components (Main) | Vehicle speed sensor
Combination meter assembly Skid control ECU (Brake actuator assembly) |
| Required Sensors/Components (Related) | Park/neutral position switch*1
Engine coolant temperature sensor Crankshaft position sensor Throttle position sensor Mass air flow meter |
| Frequency of Operation | Continuous |
*1: for CVT
| Engine | Running |
| Fuel cut | On |
| Vehicle speed sensor signal | No signal |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine.
On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT /Data List / Idle Fuel Cut.
Drive the vehicle at 74 km/h (46 mph) or higher for a total of 10 seconds or more [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [E].
Stop the vehicle
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0500.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.
| Tester Display |
|---|
| Vehicle Speed |
Drive the vehicle.
Read the value displayed on the GTS.
| Result | Proceed to |
|---|---|
| Values displayed on GTS and speedometer display not equal | A |
| Values displayed on GTS and speedometer display equal | B |
A
B
Check the circuits that send vehicle speed signals to this system in the combination meter system.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
If no DTCs (no pending DTCs) are output to the GTS, the repair has been successfully completed.
| Proceed to |
|---|
| NEXT |
NEXT