| *A | for CVT | *B | for Manual Transaxle |
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| B46-5 (+BM) - B46-3 (E1) | R - W-B | Power source of ECM | Always | 11 to 14 V |
| B46-6 (M-) - B46-4 (ME01) | BR - W-B | Throttle actuator operation signal (negative terminal) | Idling with warm engine | Pulse generation
(See waveform 1) |
| B46-7 (M+) - B46-4 (ME01) | G - W-B | Throttle actuator operation signal (positive terminal) | Idling with warm engine | Pulse generation
(See waveform 2) |
| B46-8 (OE1-) - B46-9 (OE1+) | W - L | Camshaft timing oil control valve assembly operation signal (for exhaust camshaft) | Idling | Pulse generation
(See waveform 3) |
| B46-10 (OC1-) - B46-11 (OC1+) | BR - GR | Camshaft timing oil control valve assembly operation signal (for intake camshaft) | Idling | Pulse generation
(See waveform 4) |
| B46-13 (IGT4) - B46-3 (E1) | SB - W-B | Ignition coil assembly (ignition signal) | Idling | Pulse generation
(See waveform 5) |
| B46-14 (IGT3) - B46-3 (E1) | G - W-B | |||
| B46-15 (IGT2) - B46-3 (E1) | Y - W-B | |||
| B46-16 (IGT1) - B46-3 (E1) | B - W-B | |||
| B46-18 (VTA2) - B46-28 (ETA) | GR - V | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 2.1 to 3.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 4.6 to 5.0 V | |||
| B46-21 (VCV1) - B46-3 (E1) | R - W-B | Power source of camshaft position sensor (for intake camshaft) (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| B46-22 (VV1-) - B46-23 (VV1+) | P - V | Camshaft position sensor signal (for intake camshaft) | Idling with warm engine | Pulse generation
(See waveform 6) |
| B46-24 (EV1+) - B46-32 (EV1-) | GR - G | Camshaft position sensor signal (for exhaust camshaft) | Idling with warm engine | Pulse generation
(See waveform 6) |
| B46-33 (VCNE) - B46-3 (E1) | Y - W-B | Power source of crankshaft position sensor | Ignition switch ON | 4.5 to 5.5 V |
| B46-27 (NE+) - B46-34 (NE-) | P - B | Crankshaft position sensor signal | Idling with warm engine | Pulse generation
(See waveform 7) |
| B46-29 (VCTA) - B46-28 (ETA) | W - V | Power source of throttle position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| B46-30 (VTA1) - B46-28 (ETA) | Y - V | Throttle position sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.2 to 4.8 V | |||
| B46-31 (VCE1) - B46-3 (E1) | L - W-B | Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| B47-1 (#40) - B46-1 (E01)
B47-2 (#30) - B46-1 (E01) B47-3 (#20) - B46-1 (E01) B47-4 (#10) - B46-1 (E01) |
W - W-B
Y - W-B P - W-B LG - W-B |
Fuel injector assembly signal | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(See waveform 8) |
|||
| B47-6 (HA1A) - B47-5 (E04) | R - W-B | Air fuel ratio sensor heater operation signal | Idling | Pulse generation
(See waveform 9) |
| Ignition switch ON | 11 to 14 V | |||
| B47-7 (HT1B) - B47-5 (E04) | P - W-B | Heated oxygen sensor heater operation signal | Idling | Below 3.0 V |
| Ignition switch ON | 11 to 14 V | |||
| B47-8 (EMPS) - B46-3 (E1) | B - W-B | Power steering ECU | Idling (When Steering wheel is turned to some degree) | Below 3.0 V |
| Idling (Steering wheel is neutral) | 11 to 14 V | |||
| B47-13 (PRG) - B46-1 (E01) | BR - W-B | Purge VSV operation signal | Ignition switch ON | 11 to 14 V |
| Idling, under purge control | Pulse generation
(See waveform 10) |
|||
| B47-15 (NSW)*2 - B46-3 (E1) | W - W-B | Park/neutral position switch signal | Ignition switch ON, shift lever not in P or N | 11 to 14 V |
| Ignition switch ON, shift lever in P or N | Below 3.0 V | |||
| B47-16 (LIN) - B46-3 (E1) | LG - W-B | Generator | Ignition switch ON | 11 to 14 V |
| B47-17 (STA) - B46-3 (E1) | G - W-B | Starter signal | Cranking | 5.5 V or higher |
| B47-20 (KNK1) - B47-28 (EKNK) | R - G | Knock sensor signal | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(See waveform 11) |
| B47-22 (THW) - B47-30 (ETHW) | V - L | Engine coolant temperature sensor signal | Idling, engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| B47-23 (THA) - B47-31 (ETHA) | P - BR | Intake air temperature sensor signal | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| B47-24 (VG) - B47-32 (E2G) | V - SB | Mass air flow meter signal | Idling, shift lever in P or N (neutral), A/C switch off*5 | 0.5 to 3.0 V |
| B47-26 (A1A+) - B46-3 (E1) | B - W-B*9
L - W-B*10 |
Air fuel ratio sensor signal | Always (Ignition switch ON) | 3.3 V*1 |
| B47-27 (OX1B) - B47-35 (EX1B) | GR - R | Heated oxygen sensor signal | Engine speed maintained 2500 rpm for 2 minutes after warming up sensor | Pulse generation
(See waveform 12) |
| B47-34 (A1A-) - B46-3 (E1) | W - W-B*9
P - W-B*10 |
Air fuel ratio sensor signal | Always (Ignition switch ON) | 2.9 V*1 |
| B47-14 (PBV)*2 - B46-3 (E1) | GR - W-B | Brake ejector VSV operation signal | Ignition switch ON | 11 to 14 V |
| F130-5 (FC) - B46-3 (E1) | LG - W-B | Fuel pump control | Engine stopped and ignition switch ON (fuel pump does not operate) | 11 to 14 V |
| Engine stopped and ignition switch ON (fuel pump operates) | Below 1.5 V | |||
| F130-6 (MREL) - B46-3 (E1) | L - W-B | EFI relay operation signal | Ignition switch ON | 11 to 14 V |
| F130-8 (R)*2 - B46-3 (E1) | GR - W-B | R shift position switch signal | Ignition switch ON and shift lever in R | 11 to 14 V |
| Ignition switch ON and shift lever not in R | Below 1 V | |||
| F130-11 (TACH) - B46-3 (E1) | R - W-B*9
W - W-B*10 |
Engine speed signal | Idling | Pulse generation
(See waveform 13) |
| F130-12 (ACMG)*5 - B46-3 (E1) | BE - W-B | Magnet clutch relay | All of the following conditions are met:
·
Engine running ·
Blower switch set : Lo*6 ·
Blower switch set : 1*7 ·
A/C switch off |
11 to 14 V |
| All of the following conditions are met:
·
Engine running ·
Blower switch set : Lo*6 ·
Blower switch set : 1*7 ·
A/C switch ON (magnet clutch ON) |
0 to 3.0 V | |||
| F131-30 (AC1)*5 - B46-3 (E1) | L - W-B | Magnet clutch request signal | All of the following conditions are met:
·
Engine running ·
Blower switch set : Lo*6 ·
Blower switch set : 1*7 ·
A/C switch ON (magnet clutch ON) |
11 to 14 V |
| All of the following conditions are met:
·
Engine running ·
Blower switch set : Lo*6 ·
Blower switch set : 1*7 ·
A/C switch ON (magnet clutch ON) |
0 to 3.0 V | |||
| F130-13 (CANH) - B46-3 (E1) | BE - W-B | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 14) |
| F130-14 (CANL) - B46-3 (E1) | W - W-B | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 15) |
| F130-18 (D)*2 - B46-3 (E1) | L - W-B | D shift position switch signal | Ignition switch ON and shift lever in D | 11 to 14 V |
| Ignition switch ON and shift lever not in D | Below 1 V | |||
| F130-18 (D)*3, *8 - B46-3 (E1) | G - W-B*9
L - W-B*10 |
No. 2 clutch start switch signal | Ignition switch ON, clutch pedal fully depressed | Below 1 V |
| Ignition switch ON, clutch pedal fully released | 11 to 14 V | |||
| F130-23 (SPD) - B46-3 (E1) | BR - W-B | Vehicle speed signal from combination meter assembly | Driving at 20 km/h (12 mph) | Pulse generation
(See waveform 16) |
| F130-26 (PB) - F130-35 (EPB) | L - BE | Vacuum sensor signal | Idling with warm engine, brake pedal released | 1.5 to 2.0 V |
| F130-27 (VCPB) - F130-35 (EPB) | V - BE | Power source of vacuum sensor (for PB) | Ignition switch ON | 4.75 to 5.25 V |
| F130-25 (HAC) - F130-34 (EHAC) | G - V | Atmospheric pressure sensor signal | ·
Ignition switch ON ·
Absolute pressure of 40 kPa (0.4 kgf/cm2, 5.8 psi) applied to atmospheric pressure sensor |
1.6 to 2.0 V |
·
Ignition switch ON ·
Absolute pressure of 60 kPa (0.6 kgf/cm2, 8.7 psi) applied to atmospheric pressure sensor |
2.2 to 2.6 V | |||
·
Ignition switch ON ·
Atmospheric pressure applied to atmospheric pressure sensor |
3.4 to 3.8 V | |||
| F130-33 (VHAC) - F130-34 (EHAC) | GR - V | Atmospheric pressure sensor power supply | ·
Ignition switch ON ·
Engine stopped |
4.5 to 5.5 V |
| F130-17 (ELS1) - B46-3 (E1) | V - W-B | Electric load | Tail light switch on | 7.5 to 14 V |
| Tail light switch off | Below 1.5 V | |||
| F130-28 (ELS2) - B46-3 (E1) | B - W-B | Electric load | Defogger switch on | 7.5 to 14 V |
| Defogger switch off | Below 1.5 V | |||
| F131-1 (+B) - B46-3 (E1) | R - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| F131-2 (+B2) - B46-3 (E1) | R - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| F131-3 (BATT) - B46-3 (E1) | G - W-B | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| F131-5 (FANL) - B46-3 (E1) | BR - W-B | Cooling fan relay (FAN NO. 1 relay) | ·
Ignition switch ON ·
Cooling fan not operated |
11 to 14 V |
·
Idling with A/C on*5 or high engine coolant temperature ·
Cooling fan operated |
Below 1.5 V | |||
| F131-6 (FANH) - B46-3 (E1) | LG - W-B | No. 2 cooling fan relay (FAN NO. 2 relay) | ·
Idling with high engine coolant temperature ·
Cooling fan operated at high speed |
Below 1.5 V |
| F131-16 (NEO)*4 - B46-3 (E1) | BE - W-B | Crankshaft position sensor signal | Idling with warm engine | Pulse generation
(See waveform 17) |
| F131-8 (IGSW) - B46-3 (E1) | V*9 - W-B
W*10 - W-B |
Ignition or starter switch assembly | Ignition switch ON | 11 to 14 V |
| F131-10 (STP) - B46-3 (E1) | B - W-B | Stop light switch assembly | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V | |||
| F131-11 (ST1-) - B46-3 (E1) | G - W-B | Stop light switch assembly | Ignition switch ON, Brake pedal depressed | Below 1.5 V |
| Ignition switch ON, Brake pedal released | 7.5 to 14 V | |||
| F131-19 (TC) - B46-3 (E1) | L - W-B | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| F131-20 (VCPA) - F131-27 (EPA) | G - BR | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| F131-22 (VCP2) - F131-29 (EPA2) | W - B | Power source of accelerator pedal rod assembly (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| F131-26 (VPA) - F131-27 (EPA) | P - BR | Accelerator pedal rod assembly signal (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
| Ignition switch ON, accelerator pedal fully depressed | 2.6 to 4.5 V | |||
| F131-28 (VPA2) - F131-29 (EPA2) | L - B | Accelerator pedal rod assembly signal (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 1.2 to 2.0 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.4 to 4.75 V | |||
| B46-1 (E01) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
| B46-2 (E02) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
| B46-3 (E1) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
| B46-4 (ME01) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
| B47-5 (E04) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
| F131-18 (EC) - Body ground | W-B - - | Ground | Always | Below 1 Ω |
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
*2: for CVT
*3: w/ Cruise Control System
*4: w/ Theft Deterrent System
*5: w/ Air Conditioning System
*6: for Automatic air conditioning system
*7: for Manual air conditioning system
*8: for Manual Transaxle
*9: for TMMIN Made
*10: for TMT Made
WAVEFORM 1
| ECM Terminal Name | Between M- and ME01 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 2
| ECM Terminal Name | Between M+ and ME01 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 3
| ECM Terminal Name | Between OE1+ and OE1- |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling |
WAVEFORM 4
| ECM Terminal Name | Between OC1+ and OC1- |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling |
WAVEFORM 5
| ECM Terminal Name | Between IGT (1 to 4) and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 6
| ECM Terminal Name | CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 7
| ECM Terminal Name | Between NE+ and NE- |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 8
| ECM Terminal Name | Between #10 (to #40) and E01 |
| Tester Range | 20 V/DIV., 20 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 9
| ECM Terminal Name | Between HA1A and E04 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength varies in accordance with the engine operating condition.
WAVEFORM 10
| ECM Terminal Name | Between PRG and E01 |
| Tester Range | 10 V/DIV., 20 ms./DIV. |
| Condition | Idling, under purge control |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 11
| ECM Terminal Name | Between KNK1 and EKNK |
| Tester Range | 1 V/DIV., 1 ms./DIV. |
| Condition | Engine speed maintained at 4000 rpm after warming up engine |
The wavelength becomes shorter as engine speed increases.
The waveforms and amplitudes displayed differ slightly depending on the vehicle.
WAVEFORM 12
| ECM Terminal Name | Between OX1B and EX1B |
| Tester Range | 0.2 V/DIV., 200 ms./DIV. |
| Condition | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
In the Data List, the items O2S B1S2 show the ECM input values of the heated oxygen sensor.
WAVEFORM 13
| ECM Terminal Name | Between TACH and E1 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 14
| ECM Terminal Name | Between CANH and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 15
| ECM Terminal Name | Between CANL and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 16
| ECM Terminal Name | Between SPD and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Driving at 20 km/h (12 mph) |
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 17
| ECM Terminal Name | Between NEO and E1 |
| Tester Range | 5 V/DIV., 2 ms./DIV. |
| Condition | Idling with warm engine |