Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW MASTER SWITCH(for TMT Made) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0334615 POWER WINDOW MASTER SWITCH(for TMT Made) G

WINDOW / GLASS  POWER WINDOW MASTER SWITCH(for TMT Made)  INSPECTION  


PROCEDURE

Hide 84820 1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for LHD)

a.

Check the resistance.

i.
B298969C32
1.5,1.656 1.302,0.802 true 1.875,1.667 2.448,0.948 true 2.073,1.667 2.625,1.313 true 2.375,1.906 2.917,1.906 true 2.031,2.021 2.573,2.583 true 1.865,2.021 2.083,2.583 true 1.552,2.01 1.417,2.583 true 1.344,2.01 0.917,2.583 true 0.583,1.917 1.063,1.917 true 0.844,1.104 1.375,1.677 true 2.375,1.729 2.698,1.625 true 0.083,0.052 0.396,0.281 0.313,0.229 10 false *a 1.125,0.594 1.573,0.781 0.448,0.188 10 false U (*A) 2.49,0.76 3.188,1.01 0.698,0.25 10 false A (*A) 2.99,1.813 3.396,2.031 0.406,0.219 10 false U (*B) 0.708,2.635 1.135,2.844 0.427,0.208 10 false D (*C) 0.156,1.823 0.615,2.031 0.458,0.208 10 false D (*B) 2.5,2.646 2.99,2.844 0.49,0.198 10 false U (*D) 2.688,1.208 3.125,1.417 0.438,0.208 10 false D (*A) 1.25,2.646 1.688,2.844 0.438,0.198 10 false U (*C) 1.938,2.646 2.396,2.875 0.458,0.229 10 false D (*D) 0.656,0.979 0.854,1.156 0.198,0.177 10 false B 2.781,1.542 2.979,1.719 0.198,0.177 10 false E
*A for Driver Side
*B for Front Passenger Side
*C for Rear RH Side
*D for Rear LH Side
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Condition Specified Condition
4 (A) - 1 (E) Auto up Below 1 Ω
6 (U) - 4 (A)
6 (U) - 1 (E) Manual up
3 (D) - 1 (E) Manual down
4 (A) - 1 (E) Auto down
3 (D) - 4 (A)


Standard Resistance:
Front Passenger Side Switch
Tester Connection Condition Specified Condition
10 (U) - 7 (B) Up Below 1 Ω
18 (D) - 1 (E)
10 (U) - 18 (D) Off
18 (D) - 1 (E)
18 (D) - 7 (B) Down
10 (U) - 1 (E)


Standard Resistance:
Rear RH Side Switch
Tester Connection Condition Specified Condition
15 (U) - 7 (B) Up Below 1 Ω
16 (D) - 1 (E)
15 (U) - 16 (D) Off
16 (D) - 1 (E)
16 (D) - 7 (B) Down
15 (U) - 1 (E)


Standard Resistance:
Rear LH Side Switch
Tester Connection Condition Specified Condition
12 (U) - 7 (B) Up Below 1 Ω
13 (D) - 1 (E)
12 (U) - 13 (D) Off
13 (D) - 1 (E)
13 (D) - 7 (B) Down
12 (U) - 1 (E)


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B345367C05
1.76,1.083 2.083,0.406 true 2.406,1.792 2.188,1.396 true 2.052,0.208 2.406,0.406 0.354,0.198 10 false ILL- 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 2.479,1.719 2.833,1.917 0.354,0.198 10 false ILL+
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Check that the LED illuminates.

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 11 (ILL+)
Battery negative (-) → 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.



Hide 84820 2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for RHD)

a.

Check the resistance.

i.
B298969C30
1.5,1.656 1.302,0.802 true 1.875,1.667 2.448,0.948 true 2.073,1.667 2.625,1.313 true 2.375,1.906 2.917,1.906 true 2.031,2.021 2.573,2.583 true 1.865,2.021 2.083,2.583 true 1.552,2.01 1.417,2.583 true 1.344,2.01 0.917,2.583 true 0.583,1.917 1.063,1.917 true 0.583,1.333 1.083,1.667 true 0.844,1.104 1.375,1.677 true 0.083,0.052 0.396,0.281 0.313,0.229 10 false *a 1.125,0.594 1.573,0.781 0.448,0.188 10 false D (*A) 2.49,0.76 3.188,1.01 0.698,0.25 10 false A (*A) 2.99,1.813 3.396,2.031 0.406,0.219 10 false U (*B) 0.406,1.229 0.604,1.406 0.198,0.177 10 false E 0.708,2.635 1.135,2.844 0.427,0.208 10 false D (*C) 0.156,1.823 0.615,2.031 0.458,0.208 10 false D (*B) 2.5,2.646 2.99,2.844 0.49,0.198 10 false U (*D) 2.688,1.208 3.125,1.417 0.438,0.208 10 false U (*A) 1.25,2.646 1.688,2.844 0.438,0.198 10 false U (*C) 1.938,2.646 2.396,2.875 0.458,0.229 10 false D (*D) 0.656,0.979 0.854,1.156 0.198,0.177 10 false B
*A for Driver Side
*B for Front Passenger Side
*C for Rear RH Side
*D for Rear LH Side
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Driver Side Switch
Tester Connection Condition Specified Condition
4 (A) - 9 (E) Auto up Below 1 Ω
3 (U) - 4 (A)
3 (U) - 9 (E) Manual up
6 (D) - 9 (E) Manual down
4 (A) - 9 (E) Auto down
6 (D) - 4 (A)


Standard Resistance:
Front Passenger Side Switch
Tester Connection Condition Specified Condition
10 (U) - 7 (B) Up Below 1 Ω
18 (D) - 9 (E)
10 (U) - 9 (E) Off
18 (D) - 9 (E)
18 (D) - 7 (B) Down
10 (U) - 9 (E)


Standard Resistance:
Rear RH Side Switch
Tester Connection Condition Specified Condition
15 (U) - 7 (B) Up Below 1 Ω
16 (D) - 9 (E)
15 (U) - 9 (E) Off
16 (D) - 9 (E)
16 (D) - 7 (B) Down
15 (U) - 9 (E)


Standard Resistance:
Rear LH Side Switch
Tester Connection Condition Specified Condition
12 (U) - 7 (B) Up Below 1 Ω
13 (D) - 9 (E)
12 (U) - 9 (E) Off
13 (D) - 9 (E)
13 (D) - 7 (B) Down
12 (U) - 9 (E)


If the result is not as specified, replace the power window regulator master switch assembly.



b.

Check that the LED illuminates.

i.
B345367C04
1.76,1.083 2.083,0.406 true 1.073,1.771 1.219,1.406 true 2.052,0.208 2.406,0.406 0.354,0.198 10 false ILL- 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 0.938,1.792 1.292,1.99 0.354,0.198 10 false ILL+
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 17 (ILL+)
Battery negative (-) → 5 (ILL-)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.