Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH(for TMT Made) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017125 WIPER / WASHER _0334653 WIPER SWITCH(for TMT Made) G

WIPER / WASHER  WIPER SWITCH(for TMT Made)  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)

a.

Check the resistance.

i.
B347427C06
1.146,0.698 1.479,0.938 0.333,0.24 2.125,0.698 2.458,0.938 0.333,0.24 0.896,0.927 1.479,1.885 true 0.531,1.177 1.198,1.885 true 0.333,1.406 0.99,1.875 true 2.063,1.083 1.719,1.906 true 2.583,0.906 2.125,1.875 true 2.552,2.271 2.875,3 true 2.135,2.281 2.458,3.01 true 1.708,2.271 1.531,3 true 0.99,2.271 0.813,3 true 1.26,0.729 1.458,0.906 0.198,0.177 10 false A 2.24,0.74 2.458,0.906 0.219,0.167 10 false B 0.125,0.063 0.344,0.26 0.219,0.198 10 false *a 0.667,0.844 0.958,1.021 0.292,0.177 10 false +B 0.302,1.052 0.594,1.229 0.292,0.177 10 false +1 0.125,1.292 0.417,1.469 0.292,0.177 10 false +2 2.115,0.99 2.406,1.167 0.292,0.177 10 false +S 2.635,0.802 2.958,0.99 0.323,0.188 10 false +1R 2.927,2.917 3.26,3.115 0.333,0.198 10 false EW 2.531,2.927 2.865,3.125 0.333,0.198 10 false WF 1.25,2.917 1.583,3.115 0.333,0.198 10 false WR 0.5,2.917 0.833,3.115 0.333,0.198 10 false +B2
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
A-1 (+S) - A-3 (+1) OFF Below 1 Ω
INT
A-2 (+B) - A-3 (+1) MIST
LO
A-2 (+B) - A-4 (+2) HI

Front Washer Switch
Tester Connection Switch Condition Specified Condition
B-4 (EW) - B-7 (WF) ON Below 1 Ω
A-5 (WR) - A-10 (+B2)
B-4 (EW) - B-7 (WF) OFF 10 kΩ or higher
A-5 (WR) - A-10 (+B2)

Rear Wiper Switch
Tester Connection Switch Condition Specified Condition
B-4 (EW) - B-3 (+1R) ON Below 1 Ω
OFF 10 kΩ or higher

Rear Washer Switch
Tester Connection Switch Condition Specified Condition
B-4 (EW) - A-5 (WR) ON Below 1 Ω
B-4 (WF) - A-10 (+B2)
B-4 (EW) - A-5 (WR) OFF 10 kΩ or higher
B-7 (WF) - A-10 (+B2)


If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)

a.

Check the resistance.

i.
B345174C06
0.792,0.25 1.208,0.5 0.417,0.25 1.875,0.25 2.292,0.5 0.417,0.25 2.438,1.875 3,0.917 true 2.198,1.875 2.583,0.917 true 1.948,1.875 1.656,0.917 true 1.708,1.885 1.354,0.885 true 1.313,1.875 0.833,0.875 true 1.51,2.875 1.708,2.271 true 1.104,2.875 1.302,2.271 true 0.875,2.25 0.635,2.99 true 2.656,2.979 2.438,2.281 true 0.052,0.052 0.365,0.25 0.313,0.198 10 true *a 0.552,0.771 0.979,1.01 0.427,0.24 10 false +1R 1.479,0.771 1.75,1 0.271,0.229 10 false +B 1.146,0.771 1.417,1 0.271,0.229 10 false +S 3.031,0.781 3.302,1.01 0.271,0.229 10 false +2 2.594,0.781 2.865,1.01 0.271,0.229 10 false +1 0.958,0.281 1.229,0.51 0.271,0.229 10 false B 2.042,0.281 2.313,0.51 0.271,0.229 10 false A 0.917,2.938 1.188,3.167 0.271,0.229 10 false WF 1.375,2.927 1.646,3.156 0.271,0.229 10 false WR 0.365,2.917 0.635,3.146 0.271,0.229 10 false EW 2.76,2.927 3.115,3.135 0.354,0.208 10 false +B2
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
A-4 (+S) - A-2 (+1) OFF Below 1 Ω
INT
A-3 (+B) - A-2 (+1) MIST
LO
A-3 (+B) - A-1 (+2) HI

Front Washer Switch
Tester Connection Switch Condition Specified Condition
B-7 (EW) - B-4 (WF) ON Below 1 Ω
A-10 (WR) - A-5 (+B2)
B-7 (EW) - B-4 (WF) OFF 10 kΩ or higher
A-10 (WR) - A-5 (+B2)

Rear Wiper Switch
Tester Connection Switch Condition Specified Condition
B-7 (EW) - B-1 (+1R) ON Below 1 Ω
OFF 10 kΩ or higher

Rear Washer Switch
Tester Connection Switch Condition Specified Condition
B-7 (EW) - A-10 (WR) ON Below 1 Ω
B-4 (WF) - A-5 (+B2)
B-7 (EW) - A-10 (WR) OFF 10 kΩ or higher
B-4 (WF) - A-5 (+B2)


If the result is not as specified, replace the windshield wiper switch assembly.