Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW MASTER SWITCH(for TMMIN Made) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0334654 POWER WINDOW MASTER SWITCH(for TMMIN Made) G

WINDOW / GLASS  POWER WINDOW MASTER SWITCH(for TMMIN Made)  INSPECTION  


PROCEDURE

Hide 84820 1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

a.
B298969C09
1.698,1.688 1.5,0.833 true 1.875,1.667 2.448,0.948 true 2.365,1.688 2.917,1.333 true 2.375,1.906 2.917,1.906 true 2.031,2.021 2.573,2.583 true 1.865,2.021 2.083,2.583 true 1.552,2.01 1.417,2.583 true 1.344,2.01 0.917,2.583 true 0.583,1.917 1.063,1.917 true 0.583,1.333 1.208,1.688 true 0.083,0.052 0.396,0.281 0.313,0.229 10 false *a 1.302,0.635 1.75,0.823 0.448,0.188 10 false D (*A) 2.49,0.76 3.188,1.01 0.698,0.25 10 false AUTO (*A) 2.99,1.813 3.396,2.031 0.406,0.219 10 false U (*C) 0.708,2.635 1.135,2.844 0.427,0.208 10 false U (*B) 0.156,1.823 0.615,2.031 0.458,0.208 10 false D (*C) 2.5,2.646 2.99,2.844 0.49,0.198 10 false U (*D) 2.99,1.219 3.427,1.427 0.438,0.208 10 false E 1.25,2.646 1.688,2.844 0.438,0.198 10 false D (*B) 1.938,2.646 2.396,2.875 0.458,0.229 10 false D (*D) 0.177,1.229 0.625,1.417 0.448,0.188 10 false U (*A)
*A for Driver Side
*B for Front Passenger Side
*C for Rear Passenger RH Side
*D for Rear Passenger LH Side
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (AUTO) - 1 (E) Auto UP Below 1 Ω
8 (U) - 1 (E) Auto UP Below 1 Ω
8 (U) - 1 (E) Manual UP Below 1 Ω
5 (D) - 1 (E) Manual DOWN Below 1 Ω
4 (AUTO) - 1 (E) Auto DOWN Below 1 Ω
5 (D) - 1 (E) Auto DOWN Below 1 Ω
12 (U) - 1 (E) Manual UP Below 1 Ω
13 (D) - 1 (E) Manual DOWN Below 1 Ω
10 (U) - 1 (E) Manual UP Below 1 Ω
18 (D) - 1 (E) Manual DOWN Below 1 Ω
16 (U) - 1 (E) Manual UP Below 1 Ω
15 (D) - 1 (E) Manual DOWN Below 1 Ω


If the result is not as specified, replace the power window regulator master switch assembly.



b.
B345367C02
2.375,1.115 2.646,1.115 true 2.052,1.052 2.625,0.51 true 2.771,1.052 2.927,1.25 0.156,0.198 10 false E 2.677,0.427 3.104,0.583 0.427,0.156 10 false LED+ 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Check that the LED illuminates.

i.

Apply battery voltage to the power window regulator master switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 3 (LED+)
Battery negative (-) → 1 (E)
LED illuminates


If the result is not as specified, replace the power window regulator master switch assembly.