Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Rear Door) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0092745 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


PROCEDURE

Hide 85720E 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

for TMMIN Made:

i.
B342357C03
1.76,1.438 2.323,1.917 true 0.344,1.448 0.656,1.646 0.313,0.198 10 false *b 0.5,1.792 0.813,1.99 0.313,0.198 10 false *c 2.365,0.167 2.677,0.365 0.313,0.198 10 false *a 2.396,1.854 2.708,2.052 0.313,0.198 10 false *d
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


Check the operation.

1.

Apply battery voltage to the motor connector according to the table below.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.




b.

for TMT Made:

i.
B484678C02
2.771,1.938 2.26,1.448 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 1.052,1.219 1.365,1.417 0.313,0.198 10 false *b 1.104,1.604 1.417,1.802 0.313,0.198 10 false *c 2.823,1.885 3.135,2.083 0.313,0.198 10 false *d
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


Check the operation.

1.

Apply battery voltage to the motor connector according to the table below.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.




Hide 85710F 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B343867C04
1.115,1.792 1.792,1.396 true 2.99,1.792 3.302,1.99 0.313,0.198 10 false *b 3.083,1.469 3.396,1.667 0.313,0.198 10 false *c 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 0.948,1.771 1.26,1.969 0.313,0.198 10 false *d
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


for TMMIN Made:

i.

Check the operation.

1.

Apply battery voltage to the motor connector according to the table below.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.




b.

for TMT Made:

i.
B484677C02
1.313,1.917 1.865,1.427 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.104,1.865 1.333,2.073 0.229,0.208 10 false *d 2.99,1.271 3.219,1.479 0.229,0.208 10 false *c 2.938,1.667 3.167,1.875 0.229,0.208 10 false *b
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


Check the operation.

1.

Apply battery voltage to the motor connector according to the table below.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.