Home › Vehicle Exterior › WIPER / WASHER › WASHER NOZZLE(for Front Side) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017125 WIPER / WASHER _0090080 WASHER NOZZLE(for Front Side) G

WIPER / WASHER  WASHER NOZZLE(for Front Side)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85035 1.INSPECT WASHER NOZZLE SUB-ASSEMBLY

a.

for TMMIN Made:

i.

With the ignition switch to ON, check the position that the washer fluid hits the windshield glass.

Standard:

Washer fluid hits the windshield in the areas shown in the illustration.


B347424C01
1.177,1.813 1.333,1.615 false 5.938,1.896 5.802,1.677 false 1.719,3.667 1.969,3.594 false 5.177,3.615 5.417,3.583 false 1.271,2.135 1.49,1.917 true 5.885,2.177 5.667,1.927 true 1.073,1.802 1.385,1.958 0.313,0.156 10 false *a 1.135,2.135 1.448,2.292 0.313,0.156 10 false *b 1.563,3.594 1.875,3.75 0.313,0.156 10 false *c 5.885,1.896 6.198,2.052 0.313,0.156 10 false *a 5.885,2.188 6.198,2.344 0.313,0.156 10 false *b 5.458,3.479 5.771,3.635 0.313,0.156 10 false *c 3.219,0.188 3.531,0.344 0.313,0.156 10 false A 3.833,0.177 4.146,0.333 0.313,0.156 10 false A 2.698,3.073 3.01,3.229 0.313,0.156 10 false B 2.479,3.771 2.792,3.927 0.313,0.156 10 false C 3.323,4.135 3.635,4.292 0.313,0.156 10 false D 3.75,4.135 4.063,4.292 0.313,0.156 10 false D
*a Upper Limit *b Standard
*c Lower Limit - -


Standard Clearance
Area Measurement Area Measurement
A 129.2 mm (5.09 in.) B 196.5 mm (7.74 in.)
C 151.1 mm (5.95 in.) D 4.7 mm (0.185 in.)

If the result is not as specified, replace the washer nozzle sub-assembly.



b.

for TMT Made:

i.

With the ignition switch to ON, check the position that the washer fluid hits the windshield glass.

Standard:

Washer fluid hits the windshield in the areas shown in the illustration.


B487195C05
1.177,1.833 1.344,1.646 false 1.323,2.281 1.521,2.083 true 1.729,3.719 1.958,3.604 false 5.792,1.719 5.875,1.875 false 5.656,1.979 5.75,2.146 true 5.219,3.531 5.448,3.417 false 3.198,0.208 3.354,0.406 0.156,0.198 10 false A 3.823,0.219 3.979,0.417 0.156,0.198 10 false A 3.302,4.146 3.458,4.344 0.156,0.198 10 false B 3.74,4.146 3.896,4.344 0.156,0.198 10 false B 1.01,1.76 1.323,1.917 0.313,0.156 10 false *a 1.146,2.219 1.458,2.375 0.313,0.156 10 false *b 1.552,3.615 1.865,3.771 0.313,0.156 10 false *c 5.885,1.875 6.198,2.031 0.313,0.156 10 false *a 5.771,2.156 6.083,2.313 0.313,0.156 10 false *b 5.49,3.313 5.802,3.469 0.313,0.156 10 false *c
*a Upper Limit *b Standard
*c Lower Limit - -


Standard Clearance
Area Measurement Area Measurement
A 153.0 mm (6.02 in.) B 8.4 mm (0.331 in.)

If the result is not as specified, replace the washer nozzle sub-assembly.