84250A
1.INSPECT STEERING PAD SWITCH ASSEMBLY (Type A)
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Volume+ |
| *c | Volume- | *d | MODE |
| *e | Seek+ | *f | Seek- |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z9-1 (HO) - A-1 (HO) | Always | Below 2.5 Ω |
| z9-11 (AU1) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| z9-10 (AU2) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE switch pushed | Below 2.5 Ω |
If the result is not as specified, replace the steering pad switch assembly.
Check the illumination.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
- | - |
Connect a positive (+) lead from the battery to terminal z9-5 (IL+2) and a negative (-) lead to terminal z9-8 (EAU) of the steering pad switch assembly connector.
Check that the steering pad switch assembly illumination illuminates.
The steering pad switch assembly illumination illuminates.
If the result is not as specified, replace the steering pad switch assembly.
84250A
2.INSPECT STEERING PAD SWITCH ASSEMBLY (Type B)
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Volume+ |
| *c | Volume- | *d | MODE |
| *e | Seek+ | *f | Seek- |
| *g | Off Hook | *h | On Hook |
| *i | Enter | *j | Up |
| *k | Down | *l | Left |
| *m | Right | *n | Back |
| *o | TRIP | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z9-1 (HO) - A-1 (HO) | Always | Below 2.5 Ω |
| z9-11 (AU1) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| z9-10 (AU2) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 313 to 345 Ω | |
| Off hook switch pushed | 950 to 1050 Ω | |
| z9-2 (+DP) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Enter switch pushed | Below 2.5 Ω | |
| TRIP switch pushed | 313 to 345 Ω | |
| Back switch pushed | 950 to 1050 Ω | |
| z9-3 (+DP2) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Left switch pushed | Below 2.5 Ω | |
| UP switch pushed | 313 to 345 Ω | |
| Down switch pushed | 950 to 1050 Ω | |
| Right switch pushed | 2955 to 3265 Ω |
If the result is not as specified, replace the steering pad switch assembly.
Check the illumination.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
- | - |
Connect a positive (+) lead from the battery to terminal z9-5 (IL+2) and a negative (-) lead to terminal z9-8 (EAU) of the steering pad switch assembly connector.
Check that the steering pad switch assembly illumination illuminates.
The steering pad switch assembly illumination illuminates.
If the result is not as specified, replace the steering pad switch assembly.
84250A
3.INSPECT STEERING PAD SWITCH ASSEMBLY (Type C)
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Volume+ |
| *c | Volume- | *d | MODE |
| *e | Seek+ | *f | Seek- |
| *g | Off Hook | *h | On Hook |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z9-1 (HO) - A-1 (HO) | Always | Below 2.5 Ω |
| z9-11 (AU1) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| z9-10 (AU2) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 313 to 345 Ω | |
| Off hook switch pushed | 950 to 1050 Ω |
If the result is not as specified, replace the steering pad switch assembly.
Check the illumination.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
- | - |
Connect a positive (+) lead from the battery to terminal z9-5 (IL+2) and a negative (-) lead to terminal z9-8 (EAU) of the steering pad switch assembly connector.
Check that the steering pad switch assembly illumination illuminates.
The steering pad switch assembly illumination illuminates.
If the result is not as specified, replace the steering pad switch assembly.