Home › Audio / Visual / Telematics › AUDIO / VIDEO › FRONT DOOR SPEAKER(for TMMIN Made) › 2017.10–2018.01
RM30M0E _56 Audio / Visual / Telematics _017106 AUDIO / VIDEO _0335103 FRONT DOOR SPEAKER(for TMMIN Made) A

AUDIO / VIDEO  FRONT DOOR SPEAKER(for TMMIN Made)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The procedure described below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 86160 1.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

a.
E275694E01
0.865,1.177 1.156,1.427 0.292,0.25 10 true (1) 1.76,1.948 2.052,2.198 0.292,0.25 10 true (3) 2.427,0.469 2.719,0.719 0.292,0.25 10 true (2)

Engage the 2 claws to the vehicle body and temporarily install the front No. 1 speaker assembly.


b.

Using an air riveter or a hand riveter, install the front No. 1 speaker assembly with 3 new rivets.

HINT:

Install the rivets in the order shown in the illustration.


NOTICE:
·

Do not touch the cone part of the front No. 1 speaker assembly.

·
B171664C12
1.479,2.198 1.073,1.656 1.073,1.656 1.51,1.156 true 1.698,0.917 2.51,1.646 2.51,1.646 1.729,2.531 true 0.833,1.573 1.146,1.771 0.313,0.198 10 false *a 2.438,0.635 2.75,0.833 0.313,0.198 10 false *b 2.438,2.417 2.75,2.615 0.313,0.198 10 false *c 2.573,1.552 2.885,1.75 0.313,0.198 10 false *1
*1 Mandrel
*a Riveter
*b Incorrect
*c Correct


Do not pry on the rivets with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390C13
0.729,0.167 0.896,0.167 false 0.802,2.417 0.969,2.417 false 0.802,1.146 0.969,1.146 false 0.938,0.063 1.25,0.26 0.313,0.198 10 false *a 1,1.031 1.313,1.229 0.313,0.198 10 false *a 1,2.313 1.313,2.51 0.313,0.198 10 false *a 2.573,0.531 2.885,0.729 0.313,0.198 10 false *b 2.594,1.552 2.906,1.75 0.313,0.198 10 false *b 2.594,2.74 2.906,2.938 0.313,0.198 10 false *c
*a Riveter
*b Incorrect
*c Correct


Confirm that the rivets are seated properly against the front No. 1 speaker assembly.

·

Do not tilt the riveter when installing the rivets to the front No. 1 speaker assembly.

·

Do not leave any clearance between the rivet heads and front No. 1 speaker assembly.

·
B172391C11
0.719,2.146 0.906,2.146 false 0.74,0.656 0.927,0.656 false 0.969,0.542 1.313,0.76 0.344,0.219 11 false *a 0.948,2.031 1.292,2.25 0.344,0.219 11 false *a 2.49,1.031 2.833,1.25 0.344,0.219 11 false *b 2.49,2.5 2.833,2.719 0.344,0.219 11 false *c
*a Riveter
*b Incorrect
*c Correct


Do not leave any clearance between the front No. 1 speaker assembly and door. Firmly hold the 2 items together while installing the rivets.




c.

Connect the connector.


Hide 2.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74232 3.INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)

Hide 74232 4.INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)

Hide 69260 5.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 6.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH