Home › Engine / Hybrid System › 2NR-FE COOLING › COOLANT › 2017.10–2018.01
RM30M0E _51 Engine / Hybrid System _053565 2NR-FE COOLING _0259966 COOLANT A

2NR-FE COOLING  COOLANT  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:

Be sure that the ignition switch is off if you work near the electric cooling fans or radiator grille. With the ignition switch ON, the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on (w/ air conditioning system).


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

NOTICE:

To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot coolant and steam to blow out from the radiator assembly.


a.
A318444C06
1.063,1.719 1.063,1.5 false 1.729,1.729 1.979,1.729 false 0.99,1.75 1.302,1.906 0.313,0.156 10 false *a 2.031,1.656 2.344,1.813 0.313,0.156 10 false *b
*a Engine Under Cover
*b Hose


Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


b.

Loosen the radiator drain cock plug. Then drain the engine coolant.

A409633C02
4.542,0.896 4.813,0.719 true 3.563,1.896 4.531,2.01 true 1.906,1.208 3.01,1.635 true 2.573,3.333 2.865,3.063 true 4.844,0.646 5.156,0.844 0.313,0.198 10 false *3 4.583,1.958 4.896,2.156 0.313,0.198 10 false *4 1.708,1.083 2.021,1.281 0.313,0.198 10 false *1 2.375,3.25 2.688,3.448 0.313,0.198 10 false *2
*1 Radiator Cap Sub-assembly *2 Radiator Drain Cock Plug
*3 Air Release Valve *4 Reservoir Tank Cap



c.

Remove the radiator cap sub-assembly.

HINT:

Collect the engine coolant in a container and dispose of it according to the regulations in your area.



d.

Tighten the radiator drain cock plug by hand.


e.

Disconnect the hose from the radiator drain cock.


Hide 2.ADD ENGINE COOLANT

a.

Tighten the radiator drain cock plug by hand.


b.

Remove the hose from the radiator drain cock.


c.

Open the air release valve.


d.
A206788C11
2.719,0.865 2.896,0.604 false 2.208,1.573 2.469,1.792 false 2.938,0.5 3.25,0.656 0.313,0.156 10 false *a 2.521,1.729 2.833,1.885 0.313,0.156 10 false *b 2.75,1.135 3.063,1.292 0.313,0.156 10 false *c
*a Filler Tube End
*b Engine Coolant Level
*c 20 mm (0.787 in.)


Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Coolant level should be within 20 mm (0.787 in.) from the filler tube end.)

Capacity:
Transaxle Type Coolant Capacity
Continuously Variable Transaxle 4.7 liters (5.0 US qts, 4.1 Imp. qts)
Manual Transaxle
(for TMMIN Made)
4.5 liters (4.8 US qts, 4.0 Imp. qts)
Manual Transaxle
(for TMT Made)
4.6 liters (4.9 US qts, 4.0 Imp. qts)


NOTICE:

Do not substitute water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



e.

Open the reserve tank cap.


f.

Slowly pour engine coolant into the reservoir tank assembly until it reaches the full line.


g.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.

If the engine coolant level is low, add engine coolant.


h.

Close the air release valve.


i.

Install the radiator cap sub-assembly securely.


j.

Close the reserve tank cap.


k.

Bleed air from the cooling system.

NOTICE:
·

Before starting the engine, turn the A/C switch off (w/ air conditioning system).

·

Adjust the heater control to the maximum hot setting.

·

Adjust the blower speed to the low setting.



i.

Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

HINT:

The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.



ii.

After the engine has warmed up, run the engine using the following cycle for at least 7 minutes: at 3000 rpm for 5 seconds, at idle speed for 45 seconds. (Repeat this cycle at least 8 times.)


iii.

Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air from the system.

CAUTION:
When squeezing the radiator hoses:
·

Wear protective gloves.

·

Be careful as the No. 1 and No. 2 radiator hoses are hot.

·

Keep your hands away from the cooling fan.



NOTICE:
·

If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

Make sure that the reservoir tank assembly still has some engine coolant in it.

·

If the reservoir tank assembly does not have enough engine coolant, the engine may overheat or be seriously damaged.

·

If the reservoir tank assembly does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the reservoir tank assembly is filled to the full line.





l.

After the engine has cooled down, check that the engine coolant level is between the full and low lines.

If the coolant level is below the low line, add coolant to the full line.