Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2017.10–2018.01
RM30M0E _53 Suspension _057557 TIRE PRESSURE MONITORING _0280386 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Light Circuit  


DESCRIPTION

If the tire pressure warning ECU and receiver detects a disconnected connector or an open circuit between the tire pressure warning ECU and receiver and combination meter assembly, the tire pressure warning light blinks for 1 minute, and then remains on after the ignition switch ON.

WIRING DIAGRAM

for TMMIN Made



C349071E05
1.271,0.885 1.885,1.083 0.615,0.198 10 false TIRE 1.719,0.781 2.333,0.979 0.615,0.198 10 false 33 0.198,1.708 0.813,1.906 0.615,0.198 10 false F38 0.198,1.875 4.177,2.073 3.979,0.198 10 false Combination Meter Assembly 5.583,0.885 6.198,1.083 0.615,0.198 10 false IND 5.354,0.781 5.969,0.979 0.615,0.198 10 false 5 5.354,1.708 5.969,1.906 0.615,0.198 10 false F134 5.354,1.875 6.802,2.333 1.448,0.458 10 false Tire Pressure Warning ECU and Receiver

for TMT Made



C349071E06
1.271,0.885 1.885,1.083 0.615,0.198 10 false TIRE 1.719,0.781 2.333,0.979 0.615,0.198 10 false 35 0.198,1.708 0.813,1.906 0.615,0.198 10 false F38 0.198,1.875 4.177,2.073 3.979,0.198 10 false Combination Meter Assembly 5.583,0.885 6.198,1.083 0.615,0.198 10 false IND 5.354,0.781 5.969,0.979 0.615,0.198 10 false 5 5.354,1.708 5.969,1.906 0.615,0.198 10 false F134 5.354,1.875 6.802,2.333 1.448,0.458 10 false Tire Pressure Warning ECU and Receiver

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the F134 tire pressure warning ECU and receiver connector.


b.

Disconnect the F38 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMIN Made
Tester Connection Condition Specified Condition
F134-5 (IND) - F38-33 (TIRE) Always Below 1 Ω
F134-5 (IND) or F38-33 (TIRE) - Body ground Always 10 kΩ or higher

for TMT Made
Tester Connection Condition Specified Condition
F134-5 (IND) - F38-35 (TIRE) Always Below 1 Ω
F134-5 (IND) or F38-35 (TIRE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


f.

Check the condition of the tire pressure warning light using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire pressure warning light OFF or ON Confirm that the vehicle is stopped with the engine idling.
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Tire Pressure Warning System
50004 122 57
OK:

The tire pressure warning light turns on or off in accordance with the GTS operation.



Result:
Result Proceed to
OK (for Sedan) A
OK (for Hatchback) B
NG C



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

C