87940
1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Check the operation of the mirror surface.
Apply battery voltage and check the operation of the outer rear view mirror assembly LH.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 9 (MV)
Battery negative (-) → Terminal 8 (M+) |
Turns upward |
| Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 9 (MV) |
Turns downward |
| Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 8 (M+) |
Turns left |
| Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 4 (MH) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly LH.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Check the operation of the retractable mirror.
(w/ Power Retract Mirror)
Disconnect and reconnect the battery between each mirror position check.
The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.
| Measurement Condition | Mirror Position | Specified Condition |
|---|---|---|
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Forward position (A) | Moves from (A) to retracted position (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Forward position (A) | Does not move |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Position between forward position (A) and driving position (C) | Moves from (B) to forward position (A) |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Driving position (C) | Moves from (C) to retracted position (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Position between driving position (C) and retracted position (E) | Moves from (D) to driving position (C) |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Retracted position (E) | Does not move |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Retracted position (E) | Moves from (E) to driving position (C) |
If the result is not as specified, replace the outer rear view mirror assembly LH.
87910
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Check the operation of the mirror surface.
Apply battery voltage and check the operation of the outer rear view mirror assembly RH.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 9 (MV)
Battery negative (-) → Terminal 8 (M+) |
Turns upward |
| Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 9 (MV) |
Turns downward |
| Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 8 (M+) |
Turns left |
| Battery positive (+) → Terminal 8 (M+)
Battery negative (-) → Terminal 4 (MH) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly RH.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Check the operation of the retractable mirror.
(w/ Power Retract Mirror)
Disconnect and reconnect the battery between each mirror position check.
The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.
| Measurement Condition | Mirror Position | Specified Condition |
|---|---|---|
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Forward position (A) | Moves from (A) to retracted position (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Forward position (A) | Does not move |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Position between forward position (A) and driving position (C) | Moves from (B) to forward position (A) |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Driving position(C) | Moves from (C) to retracted position (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Position between driving position (C) and retracted position (E) | Moves from (D) to driving position (C) |
| Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 2 (MF) |
Retracted position (E) | Does not move |
| Battery positive (+) → Terminal 2 (MF)
Battery negative (-) → Terminal 7 (MR) |
Retracted position (E) | Moves from (E) to driving position (C) |
If the result is not as specified, replace the outer rear view mirror assembly RH.