84870A
1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retract Mirror)
| *1 | Mirror Retract Switch |
| *2 | Mirror Select Switch and Mirror Surface Adjust Switch |
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Check the mirror retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (MF) - 2 (ACC) | Extended position | Below 1 Ω |
| 1 (MR) - 5 (E2) | ||
| 4 (MF) - 5 (E2) | Retracted position | Below 1 Ω |
| 1 (MR) - 2 (ACC) |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror select switch and mirror adjust switch.
Select the mirror select switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 10 (VL) - 7 (B)
13 (M+) - 15 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 10 (VL) - 15 (E)
13 (M+) - 7 (B) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 9 (HL) - 7 (B)
13 (M+) - 15 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 9 (HL) - 15 (E)
13 (M+) - 7 (B) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Select the mirror select switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (VR) - 7 (B)
13 (M+) - 15 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 12 (VR) - 15 (E)
13 (M+) - 7 (B) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 11 (HR) - 7 (B)
13 (M+) - 15 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 11 (HR) - 15 (E)
13 (M+) - 7 (B) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Check the switch illumination.
Apply battery voltage between the terminals of the light and check the operation of the light.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 8 (ILL+)
Battery negative (-) → Terminal 14 (ILL-) |
Light comes on |
If the result is not as specified, replace the outer mirror switch assembly.
84870A
2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retract Mirror)
| *1 | Mirror Select Switch and Mirror Surface Adjust Switch |
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Check the mirror select switch and mirror adjust switch.
Select the mirror select switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (B) - 10 (VL)
13 (M+) - 15 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 7 (B) - 13 (M+)
10 (VL) - 15 (E) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 7 (B) - 9 (HL)
13 (M+) - 15 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 7 (B) - 13 (M+)
9 (HL) - 15 (E) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Select the mirror select switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (B) - 12 (VR)
13 (M+) - 15 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 7 (B) - 13 (M+)
12 (VR) - 15 (E) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 7 (B) - 11 (HR)
13 (M+) - 15 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 7 (B) - 13 (M+)
11 (HR) - 15 (E) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Check the switch illumination.
Apply battery voltage between the terminals of the light and check the operation of the light.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 8 (ILL+)
Battery negative (-) → Terminal 14 (ILL-) |
Light comes on |
If the result is not as specified, replace the outer mirror switch assembly.