Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 1NR-FE) › from 2017.10
RM30M0E _52 Drivetrain _017092 DRIVE SHAFT / PROPELLER SHAFT _0335780 FRONT DRIVE SHAFT ASSEMBLY(for 1NR-FE) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 1NR-FE)  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.
C282243

Using pliers, separate the front No. 2 axle inboard joint boot clamp.


Hide 43448F 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

a.
C282244

Using pliers, separate the front axle inboard joint boot clamp.


Hide 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C160821C10
1.365,1.24 0.979,0.75 0.979,0.75 1.781,0.771 true 0.781,0.646 1.094,0.802 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.

Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C287116

Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.


f.
C162724C03
2.906,0.531 1.521,0.313 1.521,0.313 3,0.615 true 1.344,0.208 1.542,0.375 0.198,0.167 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474D 6.REMOVE FRONT DRIVE SHAFT DAMPER RH (for CVT)

a.
C304762

Using needle-nose pliers, disengage the 2 claws engagement and separate the 2 front drive shaft damper clamps.


b.

Remove the front drive shaft damper RH and 2 front drive shaft damper clamps.


Hide 43474D 7.REMOVE FRONT DRIVE SHAFT DAMPER RH (for Manual Transaxle)

a.

for TMT Made:

i.
C304762

Using needle-nose pliers, disengage the 2 claws engagement and separate the 2 front No. 2 drive shaft damper clamps.


ii.

Remove the front No. 2 drive shaft damper RH and 2 front No. 2 drive shaft damper clamps.


iii.
C389431

Using pliers, remove the 2 front No. 1 drive shaft damper clamps.


iv.

Remove the front No. 1 drive shaft damper RH and 2 front No. 1 drive shaft damper clamps.



b.

for TMMIN Made:

i.
C389431

Using pliers, remove the 2 front drive shaft damper clamps.


ii.

Remove the front drive shaft damper RH and 2 front drive shaft damper clamps.



Hide 43447F 8.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.
C282245

Using pliers, separate the front No. 2 axle outboard joint boot clamp.


Hide 43447E 9.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.
C282246

Using pliers, separate the front axle outboard joint boot clamp.


Hide 10.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the front drive outboard joint shaft assembly.


Hide 41336E 11.REMOVE FRONT DRIVE SHAFT DUST COVER

a.
C235586E01
1.885,1.448 2.698,1.688 true 2.74,1.615 3.198,1.813 0.458,0.198 10 false SST

Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the front drive inboard joint assembly.

·

Do not overtighten SST.