Use the same procedure for the LH side and RH side.
The procedure listed below is for the LH side.
| *a | Centering Bolt |
| *b | Standard Bolt |
Centering bolts are used to mount the door hinge to the vehicle body and the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.
Specified torque for standard bolts is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
67004
1.INSPECT REAR DOOR PANEL SUB-ASSEMBLY (for Sedan)
Check that the clearance measurements are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 4.0 to 7.0 mm (0.157 to 0.276 in.) | B | 5.5 to 8.5 mm (0.217 to 0.335 in.) |
| C | 4.0 to 7.0 mm (0.157 to 0.276 in.) | D | 5.2 to 8.2 mm (0.205 to 0.323 in.) |
| E | 4.0 to 7.0 mm (0.157 to 0.276 in.) | F | 5.9 to 8.9 mm (0.232 to 0.350 in.) |
| G | 2.9 to 5.9 mm (0.114 to 0.232 in.) | H | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
| I | 2.9 to 5.9 mm (0.114 to 0.232 in.) | J | -1.5 to 1.5 mm (-0.059 to 0.059 in.) |
| K | 4.5 to 7.5 mm (0.177 to 0.295 in.) | L | 3.2 to 5.6 mm (0.126 to 0.220 in.) |
| M | -1.2 to 1.2 mm (-0.047 to 0.047 in.) | N | 4.4 mm (0.173 in.) |
67004
2.INSPECT REAR DOOR PANEL SUB-ASSEMBLY (for Hatchback)
Check that the clearance measurements are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 4.0 to 7.0 mm (0.157 to 0.276 in.) | B | 4.7 to 7.7 mm (0.185 to 0.303 in.) |
| C | 4.0 to 7.0 mm (0.157 to 0.276 in.) | D | 3.9 to 6.9 mm (0.154 to 0.272 in.) |
| E | 4.8 to 7.8 mm (0.189 to 0.307 in.) | F | 3.6 to 6.6 mm (0.142 to 0.260 in.) |
| G | 2.9 to 5.9 mm (0.114 to 0.232 in.) | H | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
| I | 2.9 to 5.9 mm (0.114 to 0.232 in.) | J | -1.5 to 1.5 mm (-0.0590 to 0.0590 in.) |
| K | 4.5 to 7.5 mm (0.177 to 0.295 in.) | L | 3.2 to 5.6 mm (0.126 to 0.220 in.) |
| M | -1.2 to 1.2 mm (-0.047 to 0.047 in.) | N | 4.4 mm (0.173 in.) |
67004
3.ADJUST REAR DOOR PANEL SUB-ASSEMBLY
Use the same procedure for both sides.
Using SST, adjust the door horizontally and vertically by loosening the 4 body side hinge bolts.
Tighten the 4 body side hinge bolts after the adjustment.
Using SST, adjust the door horizontally and vertically by loosening the 4 door side hinge bolts.
Tighten the 4 door side hinge bolts after the adjustment.
Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.
Using a plastic-faced hammer, hit the striker to adjust its position.
Using a T40 "TORX" socket wrench, tighten the striker mounting 2 screws after the adjustment.