After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch off before inspecting CAN bus lines for a ground short.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 CAN JUNCTION CONNECTOR (for TMMIN Made)
Check the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to DLC3 |
| *c | to Brake Actuator Assembly |
| *d | to ECM |
| *e | to Airbag ECU Assembly |
| *f | to Combination Meter Assembly |
| *g | to Certification ECU (Smart Key ECU Assembly)* |
| *h | to Air Conditioning Amplifier Assembly |
| *i | to Spiral Cable with Sensor Sub-assembly |
Connection diagram
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F62-1 (CANH) | GR | DLC3 |
| F62-12 (CANL) | W | |
| F62-2 (CANH) | L | Brake actuator assembly |
| F62-13 (CANL) | W | |
| F62-3 (CANH) | BE | ECM |
| F62-14 (CANL) | W | |
| F62-4 (CANH) | B | Airbag ECU assembly |
| F62-15 (CANL) | W | |
| F62-6 (CANH) | G | Combination meter assembly |
| F62-17 (CANL) | W | |
| F62-7 (CANH) | L | Certification ECU (smart Key ECU assembly)*1 |
| F62-18 (CANL) | W | |
| F62-8 (CANH) | V | Air conditioning amplifier assembly |
| F62-19 (CANL) | W | |
| F62-9 (CANH) | R | Spiral cable with sensor sub-assembly |
| F62-20 (CANL) | W |
*1: w/ Smart Entry and Start System
NO. 23 CAN JUNCTION CONNECTOR (for TMT Made)
Check the No. 23 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 23 CAN Junction Connector) |
*b | to Brake Actuator Assembly |
| *c | to Combination Meter Assembly | *d | to No. 1 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| A60-5 (CANH) | L | Brake actuator assembly |
| A60-16 (CANL) | W | |
| F174-5 (CANH) | G | Combination meter assembly |
| F174-16 (CANL) | W | |
| F174-6 (CANH) | L | No. 1 CAN junction connector |
| F174-17 (CANL) | W |
NO. 1 CAN JUNCTION CONNECTOR (for TMT Made)
Check the No. 1 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to DLC3 |
| *c | to No. 23 CAN Junction Connector | *d | to ECM |
| *e | to Airbag ECU Assembly | *f | to Certification ECU (Smart Key ECU Assembly)*1 |
| *g | to Air Conditioning Amplifier Assembly | *h | to Steering sensor*2 |
| *i | to Power Steering ECU Assembly | - | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F62-1 (CANH) | GR | DLC3 |
| F62-12 (CANL) | W | |
| F62-2 (CANH) | L | No. 23 CAN junction connector |
| F62-13 (CANL) | W | |
| F62-3 (CANH) | BE | ECM |
| F62-14 (CANL) | W | |
| F62-4 (CANH) | B | Airbag ECU assembly |
| F62-15 (CANL) | W | |
| F62-7 (CANH) | L | Certification ECU (smart key ECU assembly)*1 |
| F62-18 (CANL) | W | |
| F62-8 (CANH) | V | Air Conditioning Amplifier Assembly |
| F62-19 (CANL) | W | |
| F62-9 (CANH) | R | Steering sensor*2 |
| F62-20 (CANL) | W | |
| F62-10 (CANH) | B | Power steering ECU assembly |
| F62-21 (CANL) | W |
*1: w/ Smart Entry and Start System
*2: w/ VSC
DLC3
Disconnect the cable from the negative (-) battery terminal.
| *1 | DLC3 | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F16-6 (CANH) - F16-14 (CANL) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F16-6 (CANH) - F16-4 (CG) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F16-14 (CANL) - F16-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F16-6 (CANH) - F16-16 (BAT) | GR - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F16-14 (CANL) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM
| *A | for CVT | *B | for Manual Transaxle |
| *a | Component without harness connected
(ECM) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connectors.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F130-13 (CANH) - F130-14 (CANL) | BE - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F130-13 (CANH) - B46-3 (E1) | BE - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F130-14 (CANL) - B46-3 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F130-13 (CANH) - F131-3 (BATT) | BE - G | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F130-14 (CANL) - F131-3 (BATT) | W - G | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (for TMMIN Made with CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A49-25 (CANH) - A49-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A49-25 (CANH) - A49-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-14 (CANL) - A49-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-25 (CANH) - A49-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A49-14 (CANL) - A49-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (for TMMIN Made with Manual Transaxle)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A48-25 (CANH) - A48-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A48-25 (CANH) - A48-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A48-14 (CANL) - A48-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A48-25 (CANH) - A48-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A48-14 (CANL) - A48-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (for TMT Made without VSC for LHD and CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A47-25 (CANH) - A47-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A47-25 (CANH) - A47-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A47-14 (CANL) - A47-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A47-25 (CANH) - A47-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A47-14 (CANL) - A47-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (for TMT Made without VSC except LHD and CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A35-25 (CANH) - A35-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A35-25 (CANH) - A35-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A35-14 (CANL) - A35-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A35-25 (CANH) - A35-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A35-14 (CANL) - A35-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (for TMT Made with VSC for LHD and CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A49-25 (CANH) - A49-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A49-25 (CANH) - A49-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-14 (CANL) - A49-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-25 (CANH) - A49-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A49-14 (CANL) - A49-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (for TMT Made with VSC except LHD and CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A48-25 (CANH) - A48-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A48-25 (CANH) - A48-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A48-14 (CANL) - A48-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A48-25 (CANH) - A48-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A48-14 (CANL) - A48-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG ECU ASSEMBLY (for TMMIN Made)
| *a | Component without harness connected
(Airbag ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the airbag ECU assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F21-13 (CANH) - F21-22 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F21-13 (CANH) - F21-25 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-22 (CANL) - F21-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-13 (CANH) - F16-16 (BAT) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F21-22 (CANL) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG ECU ASSEMBLY (for TMT Made with Curtain Shield Airbag Assembly)
| *a | Component without harness connected
(Airbag ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the airbag ECU assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F21-13 (CANH) - F21-22 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F21-13 (CANH) - F21-25 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-22 (CANL) - F21-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-13 (CANH) - F16-16 (BAT) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F21-22 (CANL) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG ECU ASSEMBLY (for TMT Made without Curtain Shield Airbag Assembly)
| *a | Component without harness connected
(Airbag ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the airbag ECU assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F21-13 (CANH) - F21-22 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F21-13 (CANH) - F21-25 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-22 (CANL) - F21-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-13 (CANH) - F16-16 (BAT) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F21-22 (CANL) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (for TMMIN Made with Smart Entry and Start System)
| *a | Component without harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the certification ECU (smart key ECU assembly) connectors.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F44-40 (CANH) - F44-18 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F44-40 (CANH) - F43-10 (E) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F44-18 (CANL) - F43-10 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F44-40 (CANH) - F43-1 (+B) | L - V | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F44-18 (CANL) - F43-1 (+B) | W - V | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (for TMT Made with Smart Entry and Start System)
| *a | Component without harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the certification ECU (smart key ECU assembly) connectors.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F44-40 (CANH) - F44-18 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F44-40 (CANH) - F43-10 (E) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F44-18 (CANL) - F43-10 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F44-40 (CANH) - F43-1 (+B) | L - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F44-18 (CANL) - F43-1 (+B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY (for TMMIN Made)
| *a | Component without harness connected
(Combination Meter Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F38-32 (CANH) - F38-31 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F38-32 (CANH) - F38-21 (ED) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F38-31 (CANL) - F38-21 (ED) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F38-32 (CANH) - F38-40 (B) | G - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F38-31 (CANL) - F38-40 (B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY (for TMT Made)
| *a | Component without harness connected
(Combination Meter Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connecter
(to Combination Meter Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F38-23 (CANH) - F38-22 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F38-23 (CANH) - F38-21 (EP) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F38-22 (CANL) - F38-21 (EP) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F38-23 (CANH) - F38-1 (B) | G - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F38-23 (CANL) - F38-1 (B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F3-11 (TX+) - F3-12 (TX-) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F3-11 (TX+) - F3-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F3-12 (TX-) - F3-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F3-11 (TX+) - F3-21 (B) | V - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F3-12 (TX-) - F3-21 (B) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the air conditioning amplifier connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F124-11 (TX+) - F124-12 (TX-) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F124-11 (TX+) - F124-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F124-12 (TX-) - F124-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F124-11 (TX+) - F16-16 (BAT) | V - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F124-12 (TX-) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (for TMMIN Made)
| *a | Component without harness connected
(Spiral Cable with Sensor Sub-assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly) |
Disconnect the spiral cable with sensor sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F116-4 (CANH) - F116-3 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F116-4 (CANH) - F116-2 (ESS) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F116-3 (CANL) - F116-2 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F116-4 (CANH) - F116-6 (BAT) | R - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F116-3 (CANL) - F116-6 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEERING SENSOR (for TMT Made with VSC)
| *a | Component without harness connected
(Steering Sensor) |
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Disconnect the steering sensor connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F147-3 (CANH) - F147-2 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F147-3 (CANH) - F147-1 (ESS) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F147-2 (CANL) - F147-1 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F147-3 (CANH) - F147-5 (BAT) | R - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F147-2 (CANL) - F147-5 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY (for TMT Made)
| *a | Component without harness connected
(Power Steering ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
Disconnect the power steering ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F12-7 (CANH) - F12-8 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F12-7 (CANH) - F11-2 (PGND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F12-8 (CANL) - F11-2 (PGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F12-7 (CANH) - F11-1 (PIG) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F12-8 (CANL) - F11-1 (PIG) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |