Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2017.10
RM30M0E _56 Audio / Visual / Telematics _068680 PARK ASSIST / MONITORING _0335855 TOYOTA PARKING ASSIST-SENSOR SYSTEM U

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  TERMINALS OF ECU  


CLEARANCE WARNING ECU ASSEMBLY


E283066E06
3.323,0.333 3.823,0.583 0.5,0.25 3.417,0.375 3.896,0.667 0.479,0.292 10 false F176

a.

Disconnect the F176 clearance warning ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F176-11 (IG) - Body ground G - Body ground IG power source signal Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V
F176-16 (E) - Body ground BR - Body ground Ground Always Below 1 Ω
F176-20 (TL) - Body ground B - Body ground Tail relay ON signal
·

Engine switch off

·

Headlight dimmer switch is in the off position


Below 1 V
·

Engine switch on (IG)

·

Headlight dimmer switch is in the tail position


11 to 14 V
F176-19 (CLSW) - Body ground L - Body ground Back sonar or clearance sonar switch assembly power source signal
·

Engine switch on (IG)

·

Back sonar or clearance sonar switch assembly off


Below 1 V
·

Engine switch on (IG)

·

Back sonar or clearance sonar switch assembly on


11 to 14 V
F176-21 (RL) - Body ground R - Body ground Reverse position signal
·

Engine switch on (IG)

·

Shift lever in any position other than R


Below 1 V
·

Engine switch on (IG)

·

Shift lever in R


11 to 14 V


c.

Reconnect the F176 clearance warning ECU assembly connector.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F176-2 (ER) - Body ground W - Body ground Clearance warning buzzer signal When sonar detects obstacle (buzzer sounds) Pulse generation
(See waveform 1)
F176-1 (BBZ) - Body ground B - Body ground Power source of clearance warning buzzer
·

Engine switch on (IG)

·

Back sonar or clearance sonar switch assembly on


11 to 14 V
F176-12 (BOR) - Body ground L - Body ground Power source for rear center sensor circuit Engine switch off Below 1 V
·

Engine switch on (IG)

·

Back sonar or clearance sonar switch assembly on


7.2 to 8.8 V
F176-13 (E1) - Body ground SB - Body ground Ground for sensor (Rear center sensor) Always Below 1 Ω
F176-14 (SOR) - Body ground L - Body ground Sensor communication signal (Rear center sensor)
·

Engine switch on (IG)

·

Back sonar or clearance sonar switch assembly on

·

Shift lever in R


Pulse generation
(See waveform 2)


e.

Using an oscilloscope, check waveform.

i.
E324896N01
0.031,1.51 0.49,1.708 0.458,0.198 10 false GND

Waveform 1 (Reference)

Item Content
Terminal No. (Symbol) F176-2 (ER) - Body ground
Tool Setting 2 V/DIV., 200 μsec./DIV.
Vehicle Condition When sonar detects obstacle (buzzer sounds)


ii.
E235241N01
0.156,0.938 0.594,1.177 0.438,0.24 10 GND

Waveform 2 (Reference)

Item Content
Terminal No. (Symbol) F176-14 (SOR) - Body ground
Tool Setting 5 V/DIV., 1 msec./DIV.
Condition
·

Engine switch on (IG)

·

Back sonar or clearance sonar switch assembly on

·

Shift lever in R