SYSTEM DESCRIPTION
The following pattern will be used: "Operation" indicates user operation using the smart entry and start system. "Expected operation of the vehicle" indicates how a known good vehicle will react in accordance with each operation. "Suspected Area/Diagnosis" indicates suspected malfunctioning areas and tips for each diagnosis if the vehicle did not react as expected.
Example: Operation No.
| Operation | - |
| Expected operation of the vehicle | - |
| Waveform or Output Value | - |
| Suspected Area | Diagnosis |
|---|---|
| - | - |
BASIC PRECAUTIONS
DTC numbers and ECU Data Lists of the smart entry and start system can be checked using the GTS.
Check for DTCs using the following procedure. If any DTCs are output, diagnose those DTCs first.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Enter the following menus: Body Electrical / Entry&Start, Power Source Control or Starting Control / Trouble Codes.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
If cancel is selected for the smart entry and start system customize setting, cancel the smart key cancel setting.
DIAGRAM OF SMART ENTRY AND START SYSTEM (for TMMIN Made)
DIAGRAM OF SMART ENTRY AND START SYSTEM (for TMT Made)
MULTI CHANNEL FUNCTION
The electrical key transmitter sub-assembly and door control receiver can operate on two different RF channels. When an electrical key transmitter sub-assembly is brought within an exterior detection area, key verification begins. If key verification fails due to wave interference, the channel will be switched and key verification will be performed again.
The multi channel system begins verification using the channel on which the last verification was successfully performed. When verification fails, the system switches to the other channel.
| *a | Exterior detection areas are created using LF waves to receive a response from the electrical key transmitter sub-assembly. | *b | When the electrical key transmitter sub-assembly is brought into an exterior detection area, it receives LF waves from the vehicle. Using RF waves, the electrical key transmitter sub-assembly responds to the vehicle. |
| *c | Upon receiving the response from the electrical key transmitter sub-assembly, the certification ECU (smart key ECU assembly) activates the electrical key antennas (outside) one by one. Using LF waves, the certification ECU (smart key ECU assembly) determines which exterior detection area the electrical key transmitter sub-assembly is in. | *d | The electrical key transmitter sub-assembly receives the LF waves from the vehicle and responds using RF waves. (The certification ECU (smart key ECU assembly) recognizes which exterior detection area the electrical key transmitter sub-assembly is in.) |
| *e | The certification ECU (smart key ECU assembly) sends registered key ID information to the electrical key transmitter sub-assembly using LF waves. (Up to 4 key IDs can be registered.) | *f | The electrical key transmitter sub-assembly sends the key ID information using RF waves. When the certification ECU (smart key ECU assembly) receives it, verification completes. |
| *g | Wave interference (Channel switching) | - | - |
The multi channel system changes the channels when the RF band (*b, *d and *f) is interrupted by wave interference. Refer to the table below to confirm when the system changes the channels.
| *b or *d is NG | *f is NG | |||
|---|---|---|---|---|
| Condition | RF waves cannot be received | RF waves cannot be received properly | RF waves cannot be received | RF waves cannot be received properly |
| Channel switching | The channels will not be switched. | The channels will be switched. | The channels will not be switched. | The channels will be switched*. |
*: The channels are not switched during vehicle interior verification after an entry lock operation is performed.
DIAGNOSIS IN ACCORDANCE WITH USER OPERATION
Operation 1
| Operation | Turn the engine switch off and lock all the doors, then take the electrical key transmitter sub-assembly approximately 3 m (9.84 ft.) or more away from the vehicle. |
Operation 2
| Operation | While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for driver door).
Signal transmission (for TMMIN Made): Certification ECU (smart key ECU assembly) → No. 1 indoor electrical key antenna assembly → Electrical key transmitter sub-assembly → Door control receiver → Certification ECU (smart key ECU assembly) → Body computer Signal transmission (for TMT Made): Certification ECU (smart key ECU assembly) → Front door outside handle assembly (for driver door) (electrical key antenna) → Electrical key transmitter sub-assembly → Door control receiver → Certification ECU (smart key ECU assembly) → Body computer |
| Expected operation of the vehicle | While the doors are unlocked, the answer back is performed at the same time. If they do not, any of the parts listed in the table below may be malfunctioning. |
| Waveform or Output Value | ·
Pulse generation (F44-31 (CLG1) - F43-10 (E)*3)*1 ·
Pulse generation (F44-9 (CLG5) - F43-10 (E)*3)*2 ·
Pulse generation (F44-3 (RCO) - F43-10 (E)*3) ·
Pulse generation (F44-22 (RDAS) - F43-10 (E)*3) ·
Pulse generation (F44-21 (CSEL) - F43-10 (E)*3) |
*1: for TMMIN Made
*2: for TMT Made
| Suspected Area | Diagnosis |
|---|---|
| Electrical key transmitter sub-assembly | ·
The key ID code sent by the electrical key transmitter sub-assembly does not match the key ID code stored in the certification ECU (smart key ECU assembly). Use another electrical key transmitter sub-assembly to check the operation. ·
Press the lock and unlock buttons of the electrical key transmitter sub-assembly to check the operation. If the doors can be locked and unlocked, that means the detection area has not been formed. Parts other than the electrical key transmitter sub-assemblies and "Certification ECU (smart key ECU assembly)" may be malfunctioning. ·
If the electrical key transmitter sub-assembly malfunctions, the engine cannot be started and the engine switch cannot be turned on (ACC or IG). Under normal operation, the smart warning light in the combination meter assembly blinks green slowly*1 or smart warning light is displayed on the multi-information display in the combination meter assembly*2 when the engine switch is pressed with the electrical key transmitter sub-assembly in the driver seat area, the shift lever in P*3 and the brake pedal*3 or clutch pedal*4 released. If the door cannot be opened, use the mechanical key installed in the electrical key transmitter sub-assembly to open the door.
|
| Transmitter battery is depleted | ·
Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the transmitter LED blinks. If the transmitter LED does not blink or blinks only once or twice, the transmitter battery may be depleted. If the transmitter LED does not blink at all, the electrical key transmitter sub-assembly may be malfunctioning. ·
If the transmitter battery voltage at the time the electrical key transmitter sub-assembly sends a signal drops to 2.1 V or less, "Yes" is displayed for "Key Low Battery" in the Data List. ·
If the transmitter battery voltage drops to 2.0 V or lower, operation cannot be assured.
·
When the transmitter battery is depleted, the engine cannot be started and the engine switch cannot be turned on (ACC or IG). If the electrical key transmitter sub-assembly is held near the engine switch the engine can be started. ·
Make sure that the transmitter battery type and installation direction are correct. |
| Wave Interference | ·
If the problem occurs in certain locations or times of day, the possibility of wave interference is high. ·
When the electrical key transmitter sub-assembly is malfunctioning, the transmitter battery is depleted, an electrical key transmitter sub-assembly from another vehicle has been used or wave interference is suspected. "Yes" may be displayed for any of the following Data List items: "Unmatch Code or Form", "No Response", "ID Code Difference" or "Unmatched Vehicle-ID" |
| Certification ECU (smart key ECU assembly) | ·
When the certification ECU (smart key ECU assembly) is malfunctioning, wireless unlock cannot be performed. ·
When the certification ECU (smart key ECU assembly) is malfunctioning, ACC ON and engine start (excluding emergency operation) cannot be performed. |
| No. 1 indoor electrical key antenna assembly (center pillar LH)*5, *7 | Vehicle exterior detection area is not formed properly.
·
Even if the vehicle exterior detection area is not formed properly, the engine switch can be turned on (ACC) and the engine can be started. ·
Under normal operation, "ON" is displayed for the Data List item "D-Door Trigger Switch" when the trigger switch is pressed. |
| No. 1 indoor electrical key antenna assembly (center pillar RH)*6, *7 | Vehicle exterior detection area is not formed properly.
·
Even if the vehicle exterior detection area is not formed properly, the engine switch can be turned on (ACC) and the engine can be started. ·
Under normal operation, "ON" is displayed for the Data List item "D-Door Trigger Switch" when the trigger switch is pressed. |
| Front door outside handle assembly (for Driver Door) (electrical key antenna)*8 | Vehicle exterior detection area is not formed properly.
·
Even if the vehicle exterior detection area is not formed properly, the engine switch can be turned on (ACC) and the engine can be started. ·
Under normal operation, "ON" is displayed for the Data List item "D-Door Trigger Switch" when the trigger switch is pressed. |
| Door Control Receiver | ·
If the door control receiver is malfunctioning, it is not possible to unlock the doors by a wireless unlock operation. ·
If the door control receiver is malfunctioning, the engine cannot be started and the engine switch cannot be turned on (ACC or IG) unless in an emergency. |
| Vehicle Battery is discharged | It may be possible to tell whether the vehicle battery is discharged by operating the horn. |
| Door lock/unlock mechanism | If a door cannot be locked/unlocked by operating the door control switch on the door in the cabin, the door lock mechanism is malfunctioning. |
| Others | ·
If the smart entry and start system function has been cancelled through the customize function, the detection area will not be formed and the door lock function will not operate even if the trigger switch is pressed. ·
If the electrical key transmitter sub-assembly is in transmitter battery saving mode, even if it receives LF waves from the vehicle, it does not respond using RF waves, therefore the electrical key transmitter sub-assembly LED does not blink. |
*1: w/ Multi-information Display (Segment LCD Type)
*2: w/ Multi-information Display (Color TFT Type)
*3: for CVT
*4: for Manual Transaxle
*5: for LHD
*6: for RHD
*7: for TMMIN Made
*8: for TMT Made
Operation 3
| Operation | After getting into the vehicle while carrying the electrical key transmitter sub-assembly, close the door and press the engine switch once with the shift lever in P*1 while not depressing the brake pedal*1 or clutch pedal*2. |
| Expected operation of the vehicle | ·
The smart warning light in the combination meter assembly blinks green slowly, and the engine switch is turned on (ACC). ·
The blinking security indicator light goes off, and then the set immobiliser function cancels, allowing the vehicle to be driven. ·
The steering wheel is unlocked. If it does not, the parts listed below may be malfunctioning.
|
| Waveform or Output Value | ·
Pulse generation (F44-22 (RDAS) - F43-10 (E)*6) ·
Pulse generation (F44-31 (CLG1) - F43-10 (E)*6) ·
Pulse generation (F44-6 (CLG2) - F43-10 (E)*6) ·
Pulse generation (F44-26 (CLG6) - F43-10 (E)*6)*5 |
*1: for CVT
*2: for Manual Transaxle
*3: w/ Multi-information Display (Segment LCD Type)
*4: w/ Multi-information Display (Color TFT Type)
*5: for TMMIN Made
| Suspected Area | Diagnosis |
|---|---|
| Certification ECU (smart key ECU assembly) | - |
| Wave Interference | ·
If malfunctions occur at a specific location/time, wave interference may be the cause. ·
If wave interference is suspected in the cabin, disconnect all the connectors of electronic devices besides standard equipment, or remove the electronic devices and check for noise. |
| Indoor electrical key antenna assemblies that form the interior detection areas. | ·
If the interior detection areas are not formed properly, the engine cannot be started and the engine switch cannot be turned on (ACC or IG). If the electrical key transmitter sub-assembly is held near the engine switch in an emergency, the engine can be started. |
| Engine switch | Under normal operation, after the engine switch is pressed, "ON" is displayed for the Data List items "Start Switch1" and "Start Switch2". |
| Park/neutral position switch*1 | Under normal conditions, "Neutral SW/ Clutch SW" in the Data List displays "ON" when the shift lever is moved to P. |
| Steering lock ECU (steering lock actuator assembly) | ·
If "OK" is displayed for the Data List item "L Code Check" when the engine switch is turned on (ACC), power will be supplied to the steering motor for approximately 10 seconds. Then the ECU sends an unlock signal to the steering motor and the Data List item "Unlock Request Receive" temporarily changes from "NG" to "OK". After the steering unlocks the ECU receives the unlocked signal from the steering motor and the Data List item "Steering Unlock" changes from "Unset" to "Set". ·
In order to unlock the steering wheel, it is necessary that "OK" is displayed for the Data List item "L Code Check" (the ID code stored in the steering lock ECU (steering lock actuator assembly) matches that of the certification ECU (smart key ECU assembly)). |
*1: for CVT
The electrical key transmitter sub-assembly, the transmitter battery and the vehicle battery have already been inspected in the previous operation steps. However, if they have not been inspected, inspect them.
Operation 4
| Operation | Depress the brake pedal*1 or clutch pedal*2 with the shift lever in P*1 while carrying an electrical key transmitter sub-assembly. |
| Expected operation of the vehicle | The smart warning light in the combination meter assembly blinks green. If it does not, the parts listed below may be malfunctioning. |
*1: for CVT
*2: for Manual Transaxle
*1: for CVT
*2: for Manual Transaxle
Operation 5
| Operation | After getting into the vehicle while carrying the electrical key transmitter sub-assembly, press the engine switch with the shift lever in P*1 while depressing the brake pedal*1 or clutch pedal*2. |
| Expected operation of the vehicle | The engine starts. If it does not, the parts listed below may be malfunctioning. |
*1: for CVT
*2: for Manual Transaxle
| Suspected Area | Diagnosis |
|---|---|
| Steering lock system | Under normal operation, the steering wheel will be unlocked and "ON" is displayed for the Data List item "Steering Unlock Switch". |
| Vehicle Battery is discharged | Whether the vehicle battery is discharged or not can be checked easily by operating the horn. |
Operation 6
| Operation | Press the engine switch. |
| Expected operation of the vehicle | The engine stops, the smart warning light illuminates and then goes off and the security indicator light changes from off to blinking. |
Operation 7
| Operation | Open any of the doors with the engine switch off. |
| Expected operation of the vehicle | The steering wheel locks. If it does not, the parts listed below may be malfunctioning. |
| Suspected Area | Diagnosis |
|---|---|
| Steering lock system | - |
| Door courtesy light switch assembly | - |
Operation 8
| Operation | While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for driver door). |
| Expected operation of the vehicle | Answer back is performed at the same time when the doors are locked. |
WIRELESS DOOR LOCK BUZZER VOLUME ADJUSTMENT FUNCTION
The volume of the wireless door lock buzzer can be changed through the customize function.
The volume of the following wireless door lock buzzer operations cannot be adjusted.
Warning function buzzer operations
Customize function buzzer operations
Buzzer operations for key diagnostic mode using the GTS
Key registration buzzer operations
WARNING FUNCTION
Warning
When any of the situations below occur, the smart entry and start system causes the certification ECU (smart key ECU assembly) to sound the wireless door lock buzzer and a buzzer in the combination meter assembly and the smart warning light in the combination meter assembly to illuminate in order to alert the driver.
Situation: The engine is left running and the shift lever is in a position other than P when the driver gets out of the vehicle. (for CVT)
There are 2 patterns for this situation.
Pattern 1:
When the engine is left running and the shift lever is in a position other than P, the driver opens the door and attempts to get out of the vehicle.
In this situation, the following control is performed:
| Reason for warning | Sudden vehicle start, vehicle theft, vehicle roll-away |
| Warning Start Condition
(All conditions are met) |
·
The engine switch is on (ACC) or on (IG). ·
The shift lever is in a position other than P. ·
The driver door is opened. ·
The vehicle speed is 0 km/h (0 mph). |
| Warning description | ·
Buzzer in combination meter assembly sounds continuously. ·
"Shift to P Position When Parked" is displayed on the multi-information display in the combination meter assembly.* |
| Warning Stop Condition
(One of conditions is met) |
·
The engine switch is turned off. ·
The shift lever is in P. ·
The driver door is closed. ·
The vehicle speed is 5 km/h (3.11 mph) or more. |
*: w/ Multi-information Display (Color TFT Type)
Pattern 2:
Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly.
In this situation, the following control is performed:
| Reason for warning | Sudden vehicle start, vehicle theft, vehicle roll-away |
| Warning Start Condition
(All conditions are met) |
·
The engine switch is on (ACC) or on (IG). ·
The shift lever is in a position other than P. ·
The driver door is opened → closed. ·
The electrical key transmitter sub-assembly is not in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
| Warning description | ·
Buzzer in the combination meter assembly sounds continuously. ·
Wireless buzzer sounds continuously. ·
Smart warning light flashes orange in the combination meter assembly.[C]*1 ·
"Shift to P Position When Parked"(A) and "Key Not Detected Check Key Location"(B) are displayed alternately on the multi-information display in the combination meter assembly.*2 |
| Warning Stop Condition
(One of conditions is met) |
Warning stop conditions for (A)
·
The shift lever is in P. ·
The vehicle speed is 5 km/h (3.11 mph) or more. Warning stop conditions for (B), (C) ·
The engine switch is turned off. ·
Electrical key transmitter sub-assembly is returned to the vehicle. |
*1: w/ Multi-information Display (Segment LCD Type)
*2: w/ Multi-information Display (Color TFT Type)
Situation: The key reminder sounds.
When the driver door is open, the driver turns the engine switch on (ACC) and attempts to leave the vehicle.
| Reason for warning | Vehicle theft |
| Warning Start Condition
(All conditions are met) |
Condition 1
·
The shift lever is in P.*1 ·
The engine switch is on (ACC). ·
The driver door is opened. |
| Condition 2 (Approval for 1 second or more)
·
The shift lever is in P.*1 ·
The engine switch is off. ·
The steering wheel is unlocked. ·
The driver door is opened. |
|
| Warning description | Buzzer in combination meter assembly sounds continuously at short and even intervals. |
| Warning Stop Condition
(One of conditions is met) |
The warning is stopped when one of the following conditions is met:
·
The engine switch is turned on (IG). ·
The driver door is closed. ·
The engine switch is turned off and the steering wheel is locked. |
*1: for CVT
Situation: The engine is left running with the shift lever in P*1 when the driver gets out of the vehicle.
There are 2 patterns for this situation.
Pattern 1:
When the engine is left running with the shift lever in P*1, the driver closes the driver door and attempts to leave the vehicle while carrying the electrical key transmitter sub-assembly.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft |
| Warning Start Condition
(All conditions are met) |
·
The engine switch is on (ACC) or on (IG). ·
The shift lever is in P.*1 ·
The driver door is opened → closed. ·
The electrical key transmitter sub-assembly is not in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
Wireless buzzer sounds 3 times. ·
Smart warning light flashes orange in the combination meter assembly.*2 ·
"Key Not Detected Check Key Location" is displayed on the multi-information display in the combination meter assembly.*3 |
| Warning Stop Condition
(Either condition is met) |
·
The engine switch is turned off. ·
The electrical key transmitter sub-assembly is returned to the vehicle. |
*1: for CVT
*2: w/ Multi-information Display (Segment LCD Type)
*3: w/ Multi-information Display (Color TFT Type)
Pattern 2:
Under the situation of pattern 1, the driver press the trigger switch on the front door outside handle assembly (for driver door).
In this situation, the following control is performed:
| Reason for warning | Vehicle theft |
| Warning Start Condition
(All conditions are met) |
·
The engine switch is on (ACC) or on (IG). ·
The shift lever is in P.*1 ·
The electrical key transmitter sub-assembly is not in the inside detection areas. ·
The electrical key transmitter sub-assembly is in the outside detection areas. ·
Pressed the trigger switch on the front door outside handle assembly (for driver door). ·
The vehicle speed is 0 km/h (0 mph). |
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
Wireless buzzer sounds continuously. ·
Smart warning light flashes orange in the combination meter assembly. (C)*2 ·
"Turn Power Off"(A) and "Key Not Detected Check Key Location"(B) are displayed alternately on the multi-information display in the combination meter assembly.*3 |
| Warning Stop Condition
(One of conditions is met) |
·
The engine switch is turned off. ·
With the shift lever in P, the shift lever is moved to a position other than P.*1 ·
The vehicle speed is 5 km/h (3.11 mph) or more. ·
5 seconds have elapsed after the wireless door lock buzzer is activated (only wireless buzzer stops). ·
Any door is opened or closed (only wireless buzzer stops). ·
The electrical key transmitter sub-assembly is returned to the vehicle. |
*1: for CVT
*2: w/ Multi-information Display (Segment LCD Type)
*3: w/ Multi-information Display (Color TFT Type)
Situation: The engine is left running when a passenger gets out of the vehicle while carrying the electrical key transmitter sub-assembly.
When the engine is left running, a passenger leaves the vehicle while carrying the electrical key transmitter sub-assembly.
In this situation, the following control is performed:
| Reason for warning | Engine cannot be restarted |
| Warning Start Condition
(All conditions are met) |
·
The engine switch is on (ACC) or on (IG). ·
A door other than the driver door is opened → closed. ·
The electrical key transmitter sub-assembly is not in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
Wireless buzzer sounds 3 times. ·
Smart warning light flashes orange in the combination meter assembly.*1 ·
"Key Not Detected Check Key Location" is displayed on the multi-information display in the combination meter assembly.*2 |
| Warning Stop Condition
(Either condition is met) |
·
The engine switch is turned off. ·
The electrical key transmitter sub-assembly is returned to the vehicle. |
*1: w/ Multi-information Display (Segment LCD Type)
*2: w/ Multi-information Display (Color TFT Type)
Situation: The electrical key transmitter sub-assembly is not in the detection areas.
When the electrical key transmitter sub-assembly is not in the vehicle or the transmitter battery is depleted, the driver attempts to start the engine or turn the engine switch on (IG).
In this situation, the following control is performed:
| Reason for warning | Confuses the user |
| Warning Start Condition
(All conditions are met) |
·
A door is not unlocked using the mechanical key and the engine switch is pressed. ·
The electrical key transmitter sub-assembly is not in the vehicle or the transmitter battery is depleted. ·
The immobiliser system is set. |
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
Smart warning light flashes orange in the combination meter assembly.*1 ·
"Key Not Detected Check Key Location" is displayed on the multi-information display in the combination meter assembly.*2 |
| Warning Stop Condition
(One of conditions is met) |
·
15 seconds elapse after warning starts. ·
The electrical key transmitter sub-assembly is returned to the vehicle. ·
30 seconds have elapsed after the door is opened. |
*1: w/ Multi-information Display (Segment LCD Type)
*2: w/ Multi-information Display (Color TFT Type)
Situation: The vehicle is driven without an electrical key transmitter sub-assembly.
When the vehicle starts moving without the registered electrical key transmitter sub-assembly in the vehicle.
In this situation, the following control is performed:
| Reason for warning | Engine cannot be restarted |
| Warning Start Condition
(All conditions are met) |
·
The engine switch is on (IG). ·
Warning of due to electrical key transmitter sub-assembly being brought out of vehicle is output. ·
The vehicle speed is 5 km/h (3.11 mph) or more. ·
The electrical key transmitter sub-assembly is not in the vehicle. |
| Warning description | ·
Buzzer in combination meter assembly sounds nine times. ·
Smart warning light flashes orange in the combination meter assembly.*1 ·
"Key Not Detected Check Key Location" is displayed on the multi-information display in the combination meter assembly.*2 |
| Warning Stop Condition
(Either condition is met) |
·
The engine switch is turned off. ·
The electrical key transmitter sub-assembly is returned to the vehicle. |
*1: w/ Multi-information Display (Segment LCD Type)
*2: w/ Multi-information Display (Color TFT Type)
Situation: The electrical key transmitter sub-assembly is left in the vehicle.
The trigger switch on a front door outside handle assembly (for driver door) is pressed to perform entry lock with the electrical key transmitter sub-assembly left in the vehicle.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft |
| Warning Start Condition
(All conditions are met) |
·
The engine switch is off. ·
All doors are closed. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
The trigger switch on a front door outside handle assembly (for driver door) is on (pressed). ·
Any door is unlocked. ·
The vehicle speed is 0 km/h (0 mph). |
| Warning description | ·
Wireless buzzer sounds continuously for 5 seconds. ·
"Key Detected in Vehicle" is displayed on the multi-information display in the combination meter assembly.* |
| Warning Stop Condition
(One of conditions is met) |
·
The engine switch is turned to a mode other than off. ·
The vehicle speed is 5 km/h (3.11 mph) or more. ·
Lock operation is detected. ·
Any door is opened. ·
60 seconds have elapsed after the wireless buzzer is activated.* |
*: w/ Multi-information Display (Color TFT Type)
Situation: Door is ajar.
The trigger switch on the front door outside handle assembly (for driver door) is pressed to perform entry lock with a door open.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft |
| Warning Start Condition
(All conditions are met) |
·
The engine switch is off. ·
Any door is opened. ·
The trigger switch on or lock switch is pressed on electrical key transmitter sub-assembly. ·
The electrical key transmitter sub-assembly is in the outside detection areas. |
| Warning description | Wireless buzzer sounds continuously for 5 seconds. |
| Warning Stop Condition
(One of conditions is met) |
·
The engine switch is turned to a mode other than off. ·
All doors are closed. ·
An unlock operation is performed using the wireless door lock remote function. ·
The trigger switch on the front door outside handle assembly (for driver door) is used to perform entry unlock. |
Situation: The electrical key transmitter sub-assembly is locked inside the vehicle.
With a door open and the electrical key transmitter sub-assembly in the vehicle, the lock knob is locked and then the door is closed with the door handle being pulled.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft |
| Warning Start Condition
(All conditions are met) |
·
With a door open, the lock knob is locked and then the door is closed with the door handle being pulled. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
Wireless buzzer sounds continuously for 5 seconds. ·
"Key Detected in Vehicle" is displayed on the multi-information display in the combination meter assembly.* |
| Warning Stop Condition
(One of conditions is met) |
·
60 seconds have elapsed after the warning started.* ·
The engine switch is turned to a mode other than off. ·
Any door is opened. ·
Lock operation is detected. ·
The vehicle speed is 5 km/h (3.11 mph) or more. |
*: w/ Multi-information Display (Color TFT Type)
Situation: The transmitter battery is weak.
The vehicle is driven using an electrical key transmitter sub-assembly that has a low transmitter battery.
In this situation, the following control is performed:
| Reason for warning | Usability function, engine cannot be restarted |
| Warning Start Condition
(All conditions are met) |
Condition 1
·
The engine switch is turned off after being left on (IG) for more than 20 minutes. ·
The transmitter battery voltage is low. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
| Condition 2
·
The engine is off → the engine is started. ·
The transmitter battery voltage is low. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). ·
Condition 1 is met. (past) |
|
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
Smart warning light flashes orange in the combination meter assembly.*1 ·
"Key Battery Low Replace Key Battery" is displayed on the multi-information display in the combination meter assembly.*2 |
| Warning Stop Condition
(Either condition is met) |
·
15 seconds have elapsed after the warning started. ·
The vehicle speed is 5 km/h (3.11 mph) or more. ·
The transmitter battery is replaced with a new one. |
*1: w/ Multi-information Display (Segment LCD Type)
*2: w/ Multi-information Display (Color TFT Type)
Situation: The steering wheel cannot be released.
The steering wheel cannot be released, thus the engine is prevented from starting.
The shift lever is moved to a position other than P*1 before the steering wheel is unlocked.
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition | Steering wheel cannot be unlocked. |
| Warning description | ·
Buzzer in the combination meter assembly sounds once. ·
Smart warning light flashes green in the combination meter assembly.*2 ·
"Push ENGINE Switch while Turning Steering Wheel in Either Direction" is displayed on the multi-information display in the combination meter assembly.*3 |
| Warning Stop Condition | ·
15 seconds have elapsed after the warning started. ·
Steering wheel is unlocked. |
*1: for CVT
*2: w/ Multi-information Display (Segment LCD Type)
*3: w/ Multi-information Display (Color TFT Type)
Situation: The smart entry and start system is malfunctioning.
An IG circuit malfunction, vehicle speed signal malfunction or malfunction that interferes with steering lock ECU (steering lock actuator assembly) operation has been detected.
In this situation, the following control is performed:
| Reason for warning | Malfunction detection |
| Warning Start Condition
(One of conditions is met) |
·
The steering lock ECU (steering lock actuator assembly), driver of the certification ECU (smart key ECU assembly) or unlock detection switch is malfunctioning. ·
An IG relay output circuit malfunction occurs three times or more consecutively. ·
The vehicle speed is judged as abnormal or vehicle speed signal communication is malfunctioning. ·
With the engine switch off, after the driver door is opened from a fully closed condition, the clutch start switch remains on for 300 seconds or more continuously.*1 |
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
Smart warning light flashes orange in the combination meter assembly.*2 ·
"Entry & Start System Malfunction See Owner's Manual" is displayed on the multi-information display in the combination meterassembly.*3 |
| Warning Stop Condition | ·
15 seconds have elapsed after the warning started. ·
The system returns to normal. |
*1: for Manual Transaxle
*2: w/ Multi-information Display (Segment LCD Type)
*3: w/ Multi-information Display (Color TFT Type)
Situation: The engine does not start. (Situation A)
When the engine switch is pressed, the electrical key transmitter sub-assembly cannot be detected in the vehicle two times in a row.
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition
(One of conditions is met) |
·
The immobiliser system is set. ·
The electrical key transmitter sub-assembly is not in the vehicle. ·
Key code verification error occurs when the engine switch is pressed twice or the driver door key linked unlock operation is performed. |
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
Smart warning light flashes orange in the combination meter assembly.*3 ·
"Depress Brake Pedal and Touch ENGINE Switch with Key" is displayed on the multi-information display in the combination meter assembly.*1, *4 ·
"Depress Clutch Pedal and Touch ENGINE Switch with Key" is displayed on the multi-information display in the combination meter assembly.*2, *4 |
| Warning Stop Condition
(Either condition is met) |
·
60 seconds have elapsed after the warning started. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
60 seconds have elapsed after the door is opened. |
*1: for CVT
*2: for Manual Transaxle
*3: w/ Multi-information Display (Segment LCD Type)
*4: w/ Multi-information Display (Color TFT Type)
Situation: The engine does not start. (Situation B) (w/ Multi-information Display (Color TFT Type))
There are 2 patterns for this situation.
Pattern 1:
The engine might be started (when the driver gets in the vehicle, or the engine switch is turned on (ACC)).
In this situation, the following control is performed:
| Possible effects without warning | Engine cannot be restarted |
| Warning Start Condition
(Either condition is met) |
·
After the doors are unlocked from outside the vehicle with the engine switch off, the driver door is opened. ·
With the brake pedal*1 or clutch*2 not depressed, the engine switch is turned on (ACC). |
| Warning description
(Not displayed while the opening image is displayed) |
·
"Depress Brake Pedal and Push ENGINE Switch to Start" is displayed on the multi-information display in the combination meter assembly.*1 ·
"Depress Clutch Pedal and Push ENGINE Switch to Start" is displayed on the multi-information display in the combination meter assembly.*2 |
| Warning Stop Condition
(One condition is met) |
·
20 seconds have elapsed after the warning started. ·
The engine speed is at 200 rpm or more. ·
The doors are locked from outside the vehicle. ·
The doors are locked by a wireless door lock operation from inside the vehicle. |
Pattern 2:
The power might be started (when the engine switch is on (IG)).
In this situation, the following control is performed:
| Possible effects without warning | Engine cannot be restarted |
| Warning Start Condition
(Either condition is met) |
·
With the shift lever in P*1 and the brake pedal*1 or clutch pedal*2 not depressed, the engine switch is turned on (IG) (the engine is not started). ·
The engine switch is on (IG) (the engine is not started) and the shift lever is moved from a position other than P or N to P or N. |
| Warning description | ·
"Depress Brake Pedal and Push ENGINE Switch to Start" is displayed on the multi-information display in the combination meter assembly.*1 ·
"Depress Clutch Pedal and Push ENGINE Switch to Start" is displayed on the multi-information display in the combination meter assembly.*2 |
| Warning Stop Condition
(One condition is met) |
·
The power source mode is changed to any mode other than on (IG). ·
The vehicle speed is 5 km/h (3 mph) or more. ·
The shift lever is moved to a position other than P or N. |
*1: for CVT
*2: for Manual Transaxle
Situation: Immobiliser system certification completion occurs.
When an electrical key transmitter sub-assembly with a depleted transmitter battery is held near to the engine switch while depressing the brake.
In this situation, the following control is performed:
| Reason for warning | Malfunction detection |
| Warning Start Condition | Electrical key transmitter sub-assembly certification result is OK. |
| Warning description | ·
Buzzer in combination meter assembly sounds once. ·
"Depress Brake Pedal and Push ENGINE Switch to Start" is displayed on the multi-information display in the combination meter assembly.*1, *3 ·
"Depress Clutch Pedal and Push ENGINE Switch to Start" is displayed on the multi-information display in the combination meter assembly.*2, *3 |
| Warning Stop Condition
(One condition is met) |
·
10 seconds have elapsed after the warning started. ·
The electrical key transmitter sub-assembly is detected by the vehicle. ·
The engine speed is at 500 rpm or more. ·
The vehicle can be driven. ·
The immobiliser system is set and key recognition is stopped or the key cannot be recognized. |
*3: w/ Multi-information Display (Color TFT Type)
*2: for Manual Transaxle
*1: for CVT
Situation: The engine switch cannot be turned off. (w/ Multi-information Display (Color TFT Type))
There are 2 patterns for this situation.
Pattern 1:
A warning message appears on the multi-information display when the driver attempts to turn the engine switch off with the shift lever in any position other than P or N.
In this situation, the following control is performed:
| Possible effects without warning | Discharged battery, vehicle roll-away |
| Warning Start Condition | ·
The engine switch is turned off with the shift lever in a position other than P or N. (Excluding an emergency stop by pressing the engine switch 3 times quickly or pressing and holding the engine switch for 2 seconds or more.) |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Shift to P Position When Parked" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
The shift lever is moved to P. ·
The engine switch is turned to a mode other than on (ACC). |
Pattern 2:
Under the situation of pattern 1, the shift lever is moved to P.
In this situation, the following control is performed:
| Possible effects without warning | Discharged battery, vehicle roll-away |
| Warning Start Condition | The shift lever is moved to P. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Turn Power Off" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
The power source mode is changed to a mode other than on (ACC). ·
The shift lever is in any position other than P. |
Situation: Warning buzzer sounds when engine switch operated while driving.
When the engine switch is pressed while the vehicle is being driven.
In this situation, the following control is performed:
| Reason for warning | Prevent accidental operation |
| Warning Start Condition (All conditions are met) | ·
The engine is running at 200 rpm or more. ·
The vehicle speed is 5 km/h (3.11 mph) or more. ·
The engine switch is pressed. |
| Warning description | Buzzer in combination meter assembly sounds continuously at short and even intervals. |
| Warning Stop Condition (Either condition is met) | ·
1.8 seconds have elapsed after operation of the engine switch is stopped. ·
The engine switch is turned off. |
Situation: Auto power off operation occurs. (w/ Multi-information Display (Color TFT Type))
A warning message appears on the multi-information display when automatic power off operation occurs.
In this situation, the following control is performed:
| Possible effects without warning | Discharged vehicle battery |
| Warning Start Condition
(All conditions are met) |
·
The shift lever is in P. ·
The engine switch is on (ACC) or on (IG). ·
No vehicle speed is detected and the engine is stopped. ·
The power source control system is turned off by automatic power off function. (20 minutes have elapsed with the engine switch on (ACC) or 1 hour has elapsed with the engine switch on (IG).) |
| Warning description | "Auto Power OFF to Conserve Battery" is displayed in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
10 seconds have elapsed after the warning started. ·
The engine switch is turned on (ACC) or on (IG). |