Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

When a trigger switch is pressed, the certification ECU (smart key control ECU assembly) generates a request signal and sends it to the No. 1 indoor electrical key antenna assembly (center pillar RH). The No. 1 indoor electrical key antenna assembly (center pillar RH transmits the received signal within an area of approximately 0.7 m (2.30 ft.) from the driver side door in order to detect the person carrying the electrical key transmitter sub-assembly. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar RH) (between terminals CLG2 and ANTE2, or terminals CG2B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A2 Open in Front Passenger Side Electrical Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar RH) (CLG2 - ANTE2, CG2B - CLGB) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Wire harness or connector

·

No. 1 indoor electrical key antenna assembly (center pillar RH)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
·

Power source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A2 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

E374110E09
1.208,1.021 1.823,1.219 0.615,0.198 10 false ANTE2 1.292,1.469 1.906,1.667 0.615,0.198 10 false CLGB 1.74,0.885 2.354,1.083 0.615,0.198 10 false 1 1.75,1.323 2.365,1.521 0.615,0.198 10 false 3 5.552,1.021 6.167,1.219 0.615,0.198 10 false CLG2 5.552,1.458 6.167,1.656 0.615,0.198 10 false CG2B 5.542,1.875 6.156,2.073 0.615,0.198 10 false E 5.438,2.417 6.969,2.979 1.531,0.563 10 false Certification ECU (Smart Key ECU Assembly) 5.219,1.885 5.833,2.083 0.615,0.198 10 false F43 5.25,1.708 5.865,1.906 0.615,0.198 10 false 10 5.219,1.448 5.833,1.646 0.615,0.198 10 false F44 5.219,1.01 5.833,1.208 0.615,0.198 10 false F44 5.281,0.823 5.896,1.021 0.615,0.198 10 false 6 5.26,1.271 5.875,1.469 0.615,0.198 10 false 23 0.542,2.427 1.156,2.625 0.615,0.198 10 false F48 0.542,2.625 2.76,3.125 2.219,0.5 10 false No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar RH)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 1 indoor electrical key antenna assembly (center pillar RH) has an antenna coil between ANTE2 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar RH).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR RH))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR RH))
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect F48 No. 1 indoor electrical key antenna assembly (center pillar RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-6 (CLG2) - F48-1 (ANTE2) Always Below 1 Ω
F44-23 (CG2B) - F48-3 (CLGB) Always Below 1 Ω
F44-6 (CLG2) or F48-1 (ANTE2) - Body ground Always 10 kΩ or higher
F44-23 (CG2B) or F48-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR RH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR RH))
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



c.

Using an oscilloscope, check the waveform.

B333754C04
2.354,0.344 2.688,0.563 0.333,0.219 4.198,0.344 4.531,0.563 0.333,0.219 1.75,2.26 1.979,1.302 true 5.188,2.24 4.875,1.302 true 4.563,2.25 4.833,1.375 true 0.177,0.156 0.49,0.313 0.313,0.156 10 false *a 2.656,2.76 2.969,2.917 0.313,0.156 10 false *b 2.927,4.177 3.24,4.333 0.313,0.156 10 false *c 3.729,4.188 4.042,4.344 0.313,0.156 10 false *d 2.406,0.365 2.865,0.563 0.458,0.198 10 false F43 4.25,0.365 4.708,0.563 0.458,0.198 10 false F44 1.698,2.313 2.156,2.51 0.458,0.198 10 false E 4.365,2.302 4.823,2.5 0.458,0.198 10 false CG2B 5.063,2.292 5.521,2.49 0.458,0.198 10 false CLG2 2.365,3.458 2.823,3.656 0.458,0.198 10 false GND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Within approximately 30 seconds from when the door is closed *d After approximately 30 seconds from when the door is closed


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-6 (CLG2) - F43-10 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
F44-23 (CG2B) - F43-10 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR RH)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR RH)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (center pillar RH) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Center Pillar)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A2 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR RH) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)