Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

for TMMIN Made:

When the luggage door opening switch assembly is pressed certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (luggage compartment). The electrical key antenna transmits the received signal within an area of approximately 0.7 m (2.30 ft.) from the luggage compartment door in order to detect the person carrying the electrical key transmitter sub-assembly. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

for TMT Made:

When the luggage door opening switch assembly*1 or back door opener switch assembly*2 is pressed, the certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage compartment). The electrical key antenna transmits the received signal within an area of approximately 0.7 m (2.30 ft.) from the luggage compartment door*1 or back door*2 in order to detect the person carrying the electrical key transmitter sub-assembly. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).

*1: for Sedan

*2: for Hatchback



DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit for TMMIN Made:

An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).


for TMT Made:

An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*).


for TMMIN Made:
·

Wire harness or connector

·

No. 3 indoor electrical key antenna assembly (luggage compartment)

·

Certification ECU (smart key ECU assembly)


for TMT Made:
·

Wire harness or connector

·

Electrical key antenna (outside luggage compartment)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry unlock operation cannot be performed for luggage compartment door*1 or back door*2 -

*1: for Sedan

*2: for Hatchback


Related Data List and Active Test
DTC Code Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

for TMMIN Made


E377892E12
5.156,1.885 5.771,2.083 0.615,0.198 10 false F43 5.156,1.448 5.771,1.646 0.615,0.198 10 false F44 5.167,1.021 5.781,1.219 0.615,0.198 10 false F44 5.552,1.021 6.167,1.219 0.615,0.198 10 false CLG8 5.563,1.448 6.177,1.646 0.615,0.198 10 false CG8B 5.552,1.875 6.167,2.073 0.615,0.198 10 false E 5.26,2.438 6.802,3.052 1.542,0.615 10 false Certification ECU (Smart Key ECU Assembly) 5.24,0.802 5.479,0.979 0.24,0.177 10 false 8 5.208,1.26 5.448,1.438 0.24,0.177 10 false 24 5.198,1.688 5.438,1.865 0.24,0.177 10 false 10 1.208,1.01 1.823,1.208 0.615,0.198 10 false ANTE8 1.281,1.427 1.896,1.625 0.615,0.198 10 false CLGB 1.781,0.885 2.021,1.063 0.24,0.177 10 false 1 1.771,1.333 2.01,1.51 0.24,0.177 10 false 3 0.583,2.396 1.198,2.594 0.615,0.198 10 false L4 0.583,2.583 2.781,3.125 2.198,0.542 10 false No. 3 Indoor Electrical Key Antenna Assembly (Luggage Compartment)


for TMT Made


E377892E11
5.167,1.885 5.781,2.083 0.615,0.198 10 false F43 5.167,1.448 5.781,1.646 0.615,0.198 10 false F44 5.167,1.01 5.781,1.208 0.615,0.198 10 false F44 5.552,1.021 6.167,1.219 0.615,0.198 10 false CLG7 5.563,1.448 6.177,1.646 0.615,0.198 10 false CG7B 5.552,1.875 6.167,2.073 0.615,0.198 10 false E 5.26,2.438 6.802,3.052 1.542,0.615 10 false Certification ECU (Smart Key ECU Assembly) 5.198,0.802 5.438,0.979 0.24,0.177 10 false 28 5.208,1.24 5.448,1.417 0.24,0.177 10 false 29 5.198,1.677 5.438,1.854 0.24,0.177 10 false 10 1.219,1.01 1.833,1.208 0.615,0.198 10 false ANTE7 1.271,1.427 1.885,1.625 0.615,0.198 10 false CLGB 1.781,0.885 2.021,1.063 0.24,0.177 10 false 2 1.771,1.333 2.01,1.51 0.24,0.177 10 false 1 0.583,2.396 1.198,2.594 0.615,0.198 10 false F152 0.583,2.583 2.583,3.146 2,0.563 10 false Electrical Key Antenna (Outside Luggage Compartment)


CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 3 indoor electrical key antenna assembly (luggage compartment) has an antenna coil between ANTE8 and CLGB terminals. (for TMMIN Made)



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specifications.

Result:
Result Proceed to
for TMMIN Made A
for TMT Made B




A

2.CHECK CONNECTOR CONNECTION

B

8.CHECK CONNECTOR CONNECTION
2.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L4 No. 3 indoor electrical key antenna assembly (luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-8 (CLG8) - L4-1 (ANTE8) Always Below 1 Ω
F44-24 (CG8B) - L4-3 (CLGB) Always Below 1 Ω
F44-8 (CLG8) or L4-1 (ANTE8) - Body ground Always 10 kΩ or higher
F44-24 (CG8B) or L4-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



c.

Using an oscilloscope, check the waveform.

B333751C05
2.5,0.313 2.917,0.563 0.417,0.25 4.417,0.313 4.833,0.563 0.417,0.25 1.917,2.25 2.177,1.333 true 4.281,2.271 4.948,1.333 true 5.385,2.271 4.969,1.396 true 3.167,4.5 3.313,3.74 true 0.406,0.271 0.719,0.427 0.313,0.156 10 false *a 2.594,2.875 2.906,3.031 0.313,0.156 10 false *b 3.073,4.49 3.385,4.646 0.313,0.156 10 false *c 2.594,0.354 3.052,0.552 0.458,0.198 10 false F43 4.521,0.344 4.979,0.542 0.458,0.198 10 false F44 1.865,2.313 2.323,2.51 0.458,0.198 10 false E 2.365,3.604 2.823,3.802 0.458,0.198 10 false GND 4.063,2.323 4.521,2.521 0.458,0.198 10 false CLG8 5.208,2.323 5.667,2.521 0.458,0.198 10 false CG8B
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Luggage door opening switch assembly is pressed - -


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-8 (CLG8) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Luggage door opening switch assembly off → on


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
F44-24 (CG8B) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Luggage door opening switch assembly off → on


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

5.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (luggage compartment) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A8 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))

NG

CONNECT CONNECTORS PROPERLY

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F152 electrical key antenna (outside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-28 (CLG7) - F152-2 (ANTE7) Always Below 1 Ω
F44-29 (CG7B) - F152-1 (CLGB) Always Below 1 Ω
F44-28 (CLG7) or F152-2 (ANTE7) - Body ground Always 10 kΩ or higher
F44-29 (CG7B) or F152-1 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)))
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



c.

Using an oscilloscope, check the waveform.

E374132C08
2.5,0.333 3,0.583 0.5,0.25 4.583,0.333 5.083,0.583 0.5,0.25 2.906,4.479 3.302,3.76 true 1.781,2.385 2.25,1.333 true 5.427,2.458 4.927,1.417 true 4.385,2.469 4.854,1.417 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 2.594,2.813 2.906,2.969 0.313,0.156 10 false *b 2.76,4.469 3.073,4.625 0.313,0.156 10 false *c 2.365,3.635 2.823,3.833 0.458,0.198 10 false GND 2.615,0.375 3.052,0.677 0.438,0.302 10 false F43 4.698,0.385 5.208,0.698 0.51,0.313 10 false F44 1.698,2.417 1.99,2.625 0.292,0.208 10 false E 5.313,2.49 5.906,2.75 0.594,0.26 10 false CLG7 4.188,2.49 4.781,2.75 0.594,0.26 10 false CG7B
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Back door opener switch assembly is pressed - -


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-28 (CLG7) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
F44-29 (CG7B) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

11.REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)
a.

Temporarily replace the electrical key antenna (outside luggage compartment) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A8 is not output.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)