Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A9  Open in Indoor Electrical Key Oscillator Circuit  


DESCRIPTION

for TMMIN Made:

When any door is opened or closed, or a trigger switch, the engine switch is pressed, the certification ECU (smart key ECU assembly) generates a request signal and sends it to the No. 2 indoor electrical key antenna assembly (rear floor). For the No. 2 indoor electrical key antenna assembly (rear floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A9 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor) (between terminals CLG6 and ANTE6, or terminals CG6B and CLGB).

for TMT Made:

When any door is opened or closed, or a trigger switch, the engine switch is pressed, the certification ECU (smart key ECU assembly) generates a request signal and sends it to the No. 1 indoor electrical key antenna assembly (instrument panel). For the No. 1 indoor electrical key antenna assembly (instrument panel) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A9 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (instrument panel) (between terminals CLG1 and ANTE1, or terminals CG1B and CLGB).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A9 Open in Indoor Electrical Key Oscillator Circuit for TMMIN Made:

An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor) (CLG6 - ANTE6, CG6B - CLGB) (1 trip detection logic*).


for TMT Made:

An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (instrument panel) (CLG1 - ANTE1, CG1B - CLGB) (1 trip detection logic*).


for TMMIN Made:
·

Wire harness or connector

·

No. 2 indoor electrical key antenna assembly (rear floor)

·

Certification ECU (smart key ECU assembly)


for TMT Made:
·

Wire harness or connector

·

No. 1 indoor electrical key antenna assembly (instrument panel)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
·

Power source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A9 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

for TMMIN Made


B286267E25
1.208,0.99 1.979,1.188 0.771,0.198 10 false ANTE6 1.271,1.438 2.042,1.635 0.771,0.198 10 false CLGB 5.531,0.979 6.302,1.177 0.771,0.198 10 false CLG6 5.531,1.854 6.302,2.052 0.771,0.198 10 false E 5.219,1 5.99,1.198 0.771,0.198 10 false F44 5.531,1.385 6.302,1.583 0.771,0.198 10 false CG6B 5.208,1.438 5.979,1.635 0.771,0.198 10 false F44 5.208,1.875 5.979,2.073 0.771,0.198 10 false F43 5.25,0.813 6.021,1.01 0.771,0.198 10 false 26 5.25,1.25 6.021,1.448 0.771,0.198 10 false 27 5.25,1.688 6.021,1.885 0.771,0.198 10 false 10 1.729,0.885 2.5,1.083 0.771,0.198 10 false 1 1.74,1.333 2.51,1.531 0.771,0.198 10 false 3 0.438,2.406 1.208,2.604 0.771,0.198 10 false F50 0.438,2.583 2.104,3.323 1.667,0.74 10 false No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) 5.198,2.417 6.74,3.115 1.542,0.698 10 false Certification ECU (Smart Key ECU Assembly)


for TMT Made


E374110E07
1.208,1.021 1.823,1.219 0.615,0.198 10 false ANTE1 1.281,1.469 1.896,1.667 0.615,0.198 10 false CLGB 1.75,1.313 2.365,1.51 0.615,0.198 10 false 3 1.76,0.854 2.375,1.052 0.615,0.198 10 false 1 5.552,1.021 6.167,1.219 0.615,0.198 10 false CLG1 5.552,1.458 6.167,1.656 0.615,0.198 10 false CG1B 5.542,1.875 6.156,2.073 0.615,0.198 10 false E 5.438,2.417 6.969,2.979 1.531,0.563 10 false Certification ECU (Smart Key ECU Assembly) 5.219,1.885 5.833,2.083 0.615,0.198 10 false F43 5.25,1.708 5.865,1.906 0.615,0.198 10 false 10 5.219,1.448 5.833,1.646 0.615,0.198 10 false F44 5.219,1.01 5.833,1.208 0.615,0.198 10 false F44 5.26,0.823 5.875,1.021 0.615,0.198 10 false 31 5.25,1.26 5.865,1.458 0.615,0.198 10 false 30 0.542,2.427 1.156,2.625 0.615,0.198 10 false F48 0.542,2.625 2.76,3.229 2.219,0.604 10 false No. 1 Indoor Electrical Key Antenna Assembly (Instrument Panel)


CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 2 indoor electrical key antenna assembly (rear floor) has an antenna coil between ANTE6 and CLGB terminals. (for TMMIN Made)



PROCEDURE

1.SYSTEM CHECK
a.

a. Check the vehicle specifications.


Result:
Result Proceed to
for TMMIN Made A
for TMT Made B



A

2.CHECK CONNECTOR CONNECTION

B

8.CHECK CONNECTOR CONNECTION
2.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F50 No. 2 indoor electrical key antenna assembly (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-26 (CLG6) - F50-1 (ANTE6) Always Below 1 Ω
F44-27 (CG6B) - F50-3 (CLGB) Always Below 1 Ω
F44-26 (CLG6) or F50-1 (ANTE6) - Body ground Always 10 kΩ or higher
F44-27 (CG6B) or F50-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



c.

Using an oscilloscope, check the waveform.

B333754C03
2.354,0.344 2.688,0.563 0.333,0.219 4.198,0.344 4.531,0.563 0.333,0.219 1.75,2.083 1.979,1.302 true 4.104,2.083 4.615,1.385 true 5.083,2.083 4.677,1.385 true 0.177,0.156 0.49,0.313 0.313,0.156 10 false *a 2.656,2.76 2.969,2.917 0.313,0.156 10 false *b 2.927,4.177 3.24,4.333 0.313,0.156 10 false *c 3.729,4.188 4.042,4.344 0.313,0.156 10 false *d 2.406,0.365 2.865,0.563 0.458,0.198 10 false F43 4.25,0.365 4.708,0.563 0.458,0.198 10 false F44 1.698,2.083 2.156,2.281 0.458,0.198 10 false E 3.885,2.094 4.344,2.292 0.458,0.198 10 false CG6B 4.938,2.083 5.396,2.281 0.458,0.198 10 false CLG6 2.365,3.458 2.823,3.656 0.458,0.198 10 false GND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Within approximately 30 seconds from when the door is closed *d After approximately 30 seconds from when the door is closed


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-26 (CLG6) - F43-10 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
F44-27 (CG6B) - F43-10 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

5.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK.:

DTC B27A6 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (instrument panel).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSTRUMENT PANEL))

NG

CONNECT CONNECTORS PROPERLY

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSTRUMENT PANEL))
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F48 No. 1 indoor electrical key antenna assembly (instrument panel) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-31 (CLG1) - F48-1 (ANTE1) Always Below 1 Ω
F44-30 (CG1B) - F48-3 (CLGB) Always Below 1 Ω
F44-31 (CLG1) or F48-1 (ANTE1) - Body ground Always 10 kΩ or higher
F44-30 (CG1B) or F48-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSTRUMENT PANEL))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSTRUMENT PANEL))
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



c.

Using an oscilloscope, check the waveform.

E374146C01
2.333,0.333 2.833,0.583 0.5,0.25 4.417,0.333 4.917,0.583 0.5,0.25 1.823,2.406 2.135,1.365 true 4.333,2.396 4.625,1.458 true 5.229,2.385 4.688,1.448 true 0.323,0.375 0.635,0.531 0.313,0.156 10 false *a 2.615,2.771 2.927,2.927 0.313,0.156 10 false *b 2.927,4.208 3.26,4.396 0.333,0.188 10 false *c 3.813,4.229 4.125,4.385 0.313,0.156 10 false *d 2.344,3.479 2.75,3.667 0.406,0.188 10 false GND 2.448,0.385 2.854,0.573 0.406,0.188 10 false F43 4.521,0.396 4.927,0.583 0.406,0.188 10 false F44 1.76,2.448 2.073,2.604 0.313,0.156 10 false E 5.167,2.438 5.656,2.813 0.49,0.375 10 false CG1B 4.167,2.438 4.656,2.813 0.49,0.375 10 false CLG1
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Within approximately 30 seconds from when the door is closed *d After approximately 30 seconds from when the door is closed


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-31 (CLG1) - F43-10 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
F44-30 (CG1B) - F43-10 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

11.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSTRUMENT PANEL)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSTRUMENT PANEL)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (instrument panel) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Instrument Panel)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK.:

DTC B27A6 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSTRUMENT PANEL) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)