Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE(for Hatchback) › from 2017.10
RM30M0E _59 Vehicle Exterior _017128 EXTERIOR PANELS / TRIM _0118069 NAME PLATE(for Hatchback) A

EXTERIOR PANELS / TRIM  NAME PLATE(for Hatchback)  INSTALLATION  


PROCEDURE

Hide 75441E 1.INSTALL NO. 1 BACK DOOR NAME PLATE (w/ Brand Name Plate)

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the back door panel.

Heating Temperature:
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)


CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 1 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 1 back door name plate as shown in the illustration.

B493485C01
4.417,3.083 4.833,2.667 false 4.229,2.979 4.542,3.135 0.313,0.156 10 false *1 4.104,1.417 4.271,1.583 0.167,0.167 10 false A 4.667,1 4.833,1.167 0.167,0.167 10 false B 5.344,2.354 5.51,2.521 0.167,0.167 10 false C 6.844,1.51 7.01,1.677 0.167,0.167 10 false D
*1 Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 15.8 mm (0.622 in.) B 44.4 mm (1.748 in.)
C 166.3 mm (6.548 in.) D 47.9 mm (1.886 in.)


NOTICE:

Install the No. 1 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 1 back door name plate to 20 to 30°C(68 to 86°F) and install the No. 1 back door name plate.



Hide 75444 2.INSTALL NO. 4 LUGGAGE COMPARTMENT DOOR PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot vehicle body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 4 luggage compartment door plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

for Type A:

i.

Install a new No. 4 back door name plate as shown in the illustration.

B499220C01
6.281,0.302 6.615,0.479 false 6.438,3.021 6.115,2.833 false 4.854,2.344 5.01,2.052 false 4.479,1.135 4.635,1.333 0.156,0.198 10 false A 5.792,0.25 5.948,0.448 0.156,0.198 10 false B 6.552,1.083 6.708,1.281 0.156,0.198 10 false C 5.417,1.719 5.573,1.917 0.156,0.198 10 false D 6.677,0.479 6.906,0.677 0.229,0.198 10 false *1 6.5,3.031 6.813,3.229 0.313,0.198 10 false *1 4.479,3.135 4.635,3.333 0.156,0.198 10 false E 6,1.802 6.156,2 0.156,0.198 10 false F 6.51,2.313 6.667,2.51 0.156,0.198 10 false G 5.667,3.51 5.823,3.708 0.156,0.198 10 false H 4.74,2.313 5.052,2.51 0.313,0.198 10 false *a 3.833,0.094 4.208,0.333 0.375,0.24 12 false *A 3.875,1.833 4.25,2.073 0.375,0.24 12 false *B
*A w/o Engine Displacement Mark *B w/ Engine Displacement Mark
*1 Back Door - -
*a R end - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 46.7 mm (1.839 in.) B 56.5 mm (2.224 in.)
C 61.9 mm (2.437 in.) D 100.9 mm (3.972 in.)
E 43.7 mm (1.720 in.) F 14.7 mm (0.579 in.)
G 57.5 mm (2.264 in.) H 59.4 mm (2.339 in.)


NOTICE:

Install the No. 4 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 4 back door name plate.




c.

for Type B:

i.

Install a new No. 4 back door name plate as shown in the illustration.

B499221C02
6.26,0.354 6.615,0.49 false 6.406,3 6.104,2.875 false 4.802,2.323 4.927,2.052 false 4.5,1.177 4.656,1.375 0.156,0.198 10 false A 5.771,0.146 5.958,0.344 0.188,0.198 10 false B 6.51,1.115 6.667,1.313 0.156,0.198 10 false C 6.656,0.438 6.875,0.635 0.219,0.198 10 false *1 5.438,1.75 5.594,1.948 0.156,0.198 10 false D 6.458,2.969 6.771,3.167 0.313,0.198 10 false *1 4.698,2.354 5.01,2.552 0.313,0.198 10 false *a 4.51,3.125 4.667,3.323 0.156,0.198 10 false E 5.99,1.802 6.146,2 0.156,0.198 10 false F 6.49,2.323 6.646,2.521 0.156,0.198 10 false G 5.656,3.5 5.813,3.698 0.156,0.198 10 false H 3.833,0.094 4.208,0.333 0.375,0.24 12 false *A 3.917,1.885 4.229,2.167 0.313,0.281 12 false *B
*A w/o Engine Displacement Mark *B w/ Engine Displacement Mark
*1 Back Door - -
*a R end - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 46.6 mm (1.835 in.) B 56.2 mm (2.213 in.)
C 61.6 mm (2.425 in.) D 100.6 mm (3.960 in.)
E 43.9 mm (1.728 in.) F 14.4 mm (0.567 in.)
G 57.7 mm (2.272 in.) H 59.1 mm (2.327 in.)


NOTICE:

Install the No. 4 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 4 back door name plate.




d.

for Type C:

i.

Install a new No. 4 back door name plate as shown in the illustration.

B499222C01
6.281,0.26 6.656,0.438 false 6.49,2.969 6.125,2.813 false 4.771,2.333 4.927,2.063 false 4.552,1.208 4.708,1.406 0.156,0.198 10 false A 5.781,0.219 5.938,0.417 0.156,0.198 10 false B 6.583,1.104 6.74,1.302 0.156,0.198 10 false C 5.427,1.729 5.583,1.927 0.156,0.198 10 false D 6.719,0.427 6.927,0.635 0.208,0.208 10 false *1 4.531,3.156 4.688,3.354 0.156,0.198 10 false E 6,1.802 6.156,2 0.156,0.198 10 false F 6.5,2.302 6.656,2.5 0.156,0.198 10 false G 5.635,3.51 5.792,3.708 0.156,0.198 10 false H 4.625,2.365 4.938,2.563 0.313,0.198 10 false *a 6.563,2.938 6.875,3.135 0.313,0.198 10 false *1 3.833,0.177 4.208,0.417 0.375,0.24 12 false *A 3.875,1.917 4.25,2.156 0.375,0.24 12 false *B
*A w/o Engine Displacement Mark *B w/o Engine Displacement Mark
*1 Back Door - -
*a R end - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 41.5 mm (1.634 in.) B 55.9 mm (2.208 in.)
C 62.6 mm (2.465 in.) D 96.1 mm (3.783 in.)
E 40.9 mm (1.610 in.) F 29.0 mm (1.142 in.)
G 54.3 mm (2.138 in.) H 57.4 mm (2.260 in.)


NOTICE:

Install the No. 4 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 4 back door name plate.




Hide 75443 3.INSTALL NO. 3 BACK DOOR NAME PLATE (w/ Engine Displacement Mark)

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 3 back door name plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 3 back door name plate as shown in the illustration.

B499231C01
6.729,0.99 6.885,1.427 false 4.104,2.229 4.26,2.427 0.156,0.198 10 false A 5.979,0.813 6.135,1.01 0.156,0.198 10 false B 6.823,2.052 7.021,2.271 0.198,0.219 10 false C 5.49,2.99 5.646,3.188 0.156,0.198 10 false D 6.938,1.375 7.125,1.573 0.188,0.198 10 false *1
*1 Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 47.7 mm (1.878 in.) B 67.0 mm (2.638 in.)
C 61.6 mm (2.425 in.) D 121.6 mm (4.787 in.)


NOTICE:

Install the No. 3 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 3 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 3 back door name plate.



Hide 75442A 4.INSTALL NO. 2 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 2 back door name plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 2 back door name plate as shown in the illustration.

B501336C01
6.333,3.115 6.083,2.802 false 6.385,3.094 6.698,3.292 0.313,0.198 10 false *1 4.375,1.385 4.531,1.583 0.156,0.198 10 false A 5.76,0.719 5.917,0.917 0.156,0.198 10 false B 6.802,1.646 6.958,1.844 0.156,0.198 10 false C 6.438,1.146 6.594,1.344 0.156,0.198 10 false D
*1 Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 23.9 mm (0.941 in.) B 153.9 mm (6.059 in.)
C 13.8 mm (0.543 in.) D 8.2 mm (0.323 in.)


NOTICE:

Install the No. 2 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 2 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 back door name plate.



Hide 75741E 5.INSTALL SYMBOL EMBLEM

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the remaining double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the symbol emblem with any double-sided tape remaining on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B484305C01
0.417,3.542 0.75,3.542 true 2.583,3.792 2.917,3.792 true 0.229,3.448 0.542,3.646 0.313,0.198 10 false *a 2.979,3.688 3.292,3.885 0.313,0.198 10 false *a
*a Location Pin


Insert the 2 location pins into the vehicle body and install a new symbol emblem.

NOTICE:

Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.