Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE(for Sedan with Rear Light) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017128 EXTERIOR PANELS / TRIM _0336573 NAME PLATE(for Sedan with Rear Light) A

EXTERIOR PANELS / TRIM  NAME PLATE(for Sedan with Rear Light)  INSTALLATION  


PROCEDURE

Hide 75441A 1.INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE (w/ Brand Name Plate)

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature:
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)


CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 1 luggage compartment door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 1 luggage compartment door name plate as shown in the illustration.

B493480C01
4.656,2.844 5.073,2.427 false 4.469,2.75 4.781,2.906 0.313,0.156 10 false *1 4.25,1.656 4.458,1.865 0.208,0.208 10 false A 4.542,0.958 4.75,1.167 0.208,0.208 10 false B 5.948,1.865 6.156,2.073 0.208,0.208 10 false C
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 38.8 mm (1.528 in.) B 22.3 mm (0.878 in.)
C 63.4 mm (2.496 in.) - -


NOTICE:

Install the No. 1 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 1 luggage compartment door name plate to 20 to 30°C(68 to 86°F) and install the No. 1 luggage compartment door name plate.



Hide 75444 2.INSTALL NO. 4 LUGGAGE COMPARTMENT DOOR PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 4 luggage compartment door plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

for Type A:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B501337C01
6.531,1.406 6.198,1.292 false 6.573,3.302 6.198,3.146 false 6.073,0.771 6.229,0.969 0.156,0.198 10 false A 5.448,0.802 5.604,1 0.156,0.198 10 false B 6.365,0.146 6.521,0.344 0.156,0.198 10 false C 6.083,2.75 6.24,2.948 0.156,0.198 10 false D 5.438,2.771 5.594,2.969 0.156,0.198 10 false E 6.323,2.177 6.479,2.375 0.156,0.198 10 false F 6.646,3.25 6.958,3.448 0.313,0.198 10 false *1 6.625,1.365 6.938,1.563 0.313,0.198 10 false *1 3.875,0.094 4.25,0.333 0.375,0.24 12 false *A 3.917,1.927 4.292,2.167 0.375,0.24 12 false *B
*A for Shark Fin Antenna Type *B for Pole Antenna Type
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 84.9 mm (3.343 in.) B 65.7 mm (2.587 in.)
C 71.0 mm (2.795 in.) D 56.9 mm (2.240 in.)
E 37.8 mm (1.488 in.) F 52.7 mm (2.075 in.)


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




c.

for Type B:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B501338C01
6.531,1.552 6.177,1.427 false 6.552,3.323 6.188,3.177 false 3.917,1.927 4.292,2.167 0.375,0.24 12 false *B 3.833,0.167 4.208,0.406 0.375,0.24 12 false *A 6.063,0.917 6.219,1.115 0.156,0.198 10 false A 5.479,0.948 5.635,1.146 0.156,0.198 10 false B 6.354,0.271 6.51,0.469 0.156,0.198 10 false C 6.094,2.719 6.25,2.917 0.156,0.198 10 false D 5.438,2.771 5.594,2.969 0.156,0.198 10 false E 6.323,2.167 6.479,2.365 0.156,0.198 10 false F 6.625,1.521 6.938,1.719 0.313,0.198 10 false *1 6.604,3.292 6.917,3.49 0.313,0.198 10 false *1
*A for Shark Fin Antenna Type *B for Pole Antenna Type
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 84.7 mm (3.334 in.) B 65.3 mm (2.570 in.)
C 70.6 mm (2.779 in.) D 56.8 mm (2.236 in.)
E 37.4 mm (1.472 in.) F 52.3 mm (2.059 in.)


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




d.

for Type C:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B499229C01
6.635,2.635 6.25,2.438 false 6.115,1.854 6.271,2.052 0.156,0.198 10 false A 5.469,1.927 5.625,2.125 0.156,0.198 10 false B 6.385,1.188 6.542,1.385 0.156,0.198 10 false C 6.719,2.615 6.948,2.813 0.229,0.198 10 false *1
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 60.4 mm (2.378 in.) B 41.4 mm (1.630 in.)
C 57.2 mm (2.252 in.) - -


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




Hide 75442 3.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

for Pole Antenna Type:

i.

Install a new No. 2 luggage compartment door name plate as shown in the illustration.

B493479C01
6.083,2.542 6.5,2.958 false 6.573,2.865 6.885,3.021 0.313,0.156 10 false *1 5.125,1.979 5.292,2.146 0.167,0.167 10 false A 6.885,1.656 7.052,1.823 0.167,0.167 10 false C 6.583,1.073 6.75,1.24 0.167,0.167 10 false B
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 70.4mm (2.772 in.) B 15.3 mm (0.602 in.)
C 28.7mm (1.130 in.) - -


NOTICE:

Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.




c.

for Shark Fin Antenna Type:

i.

Install a new No. 2 luggage compartment door name plate as shown in the illustration.

B484327C01
4.354,2.531 4.573,2.292 false 3.896,1.76 4.052,1.958 0.156,0.198 10 false A 4.271,1.219 4.427,1.417 0.156,0.198 10 false B 6.01,2.031 6.167,2.229 0.156,0.198 10 false C 4.177,2.458 4.396,2.656 0.219,0.198 10 false *1
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 39.4 mm (1.551 in.) B 21.3 mm (0.838 in.)
C 87.3 mm (3.437 in.) - -


NOTICE:

Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.




Hide 75431 4.INSTALL LUGGAGE COMPARTMENT DOOR EMBLEM

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the remaining double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the symbol emblem with any double-sided tape remaining on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B484298C01
0.427,3.552 0.74,3.552 true 2.583,3.802 2.896,3.802 true 0.25,3.458 0.563,3.656 0.313,0.198 10 false *a 2.969,3.729 3.281,3.927 0.313,0.198 10 false *a
*a Location Pin


Insert the 2 pins into the back door panel and install a new luggage compartment door emblem.

NOTICE:

Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.