75825
1.INSTALL LUGGAGE COMPARTMENT DOOR MOULDING PAD
When installing the luggage compartment door moulding pad, heat the luggage compartment door outside garnish sub-assembly using a heat light.
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
| Item | Temperature |
|---|---|
| Luggage Compartment Door Outside Garnish Sub-assembly | 20 to 30°C (68 to 86°F) |
Do not heat the luggage compartment door outside garnish sub-assembly excessively.
Clean the luggage compartment door moulding pad installation surface with a non-residue solvent.
Apply primer to the luggage compartment door moulding pad installation area on the luggage compartment door outside garnish sub-assembly.
Apply primer evenly so that there are no uncoated areas.
Remove the peeling paper on a new luggage compartment door moulding pad while making sure not to touch the adhesive surface.
Install the luggage compartment door moulding pad as shown in the illustration.
Press the double-sided tape on the luggage compartment door moulding pad firmly to ensure proper adhesion.
After the primer dries (3 minutes or more), install the luggage compartment door moulding pad.
After applying primer, reapply primer after 24 hours elapse.
75895H
2.INSTALL NO. 1 MOULDING TAPE
When installing the No. 1 moulding tape, heat the luggage compartment door outside garnish sub-assembly using a heat light.
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
| Item | Temperature |
|---|---|
| Luggage Compartment Door Outside Garnish Sub-assembly | 20 to 30°C (68 to 86°F) |
Do not heat the luggage compartment door outside garnish sub-assembly excessively.
Clean the No. 1 moulding tape installation surface with a non-residue solvent.
Apply primer to the No. 1 moulding tape installation area on the luggage compartment door outside garnish sub-assembly.
Apply primer evenly so that there are no uncoated areas.
Remove the peeling paper on a new No. 1 moulding tape while making sure not to touch the adhesive surface.
Install the No. 1 moulding tape as shown in the illustration.
Press the double-sided tape on the No. 1 moulding tape firmly to ensure proper adhesion.
After the primer dries (3 minutes or more), install the No. 1 moulding tape.
After applying primer, reapply primer after 24 hours elapse.
76801A
3.INSTALL LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH SUB-ASSEMBLY
When installing the luggage compartment door outside garnish sub-assembly, heat the vehicle body and luggage compartment door outside garnish sub-assembly using a heat light.
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Luggage Compartment Door Outside Garnish Sub-assembly | 20 to 30°C (68 to 86°F) |
Do not heat the vehicle body and luggage compartment door outside garnish sub-assembly excessively.
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Remove the peeling paper on a new luggage compartment door outside garnish sub-assembly while making sure not to touch the adhesive surface.
Engage the 6 clips and attach the double-sided tape to install the luggage compartment door outside garnish sub-assembly.
Press the double-sided tape on the luggage compartment door outside garnish sub-assembly firmly to ensure proper adhesion.
After the primer dries (3 minutes or more), install the luggage compartment door outside garnish sub-assembly.
After applying primer, reapply primer after 24 hours elapse.
81590A
4.INSTALL REAR LIGHT ASSEMBLY