Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH(for TMMIN Made) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017123 MIRROR (EXT) _0336650 OUTER MIRROR SWITCH(for TMMIN Made) G

MIRROR (EXT)  OUTER MIRROR SWITCH(for TMMIN Made)  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retract Mirror)

a.
B344830C06
0.448,1.26 0.865,0.844 true 0.583,2.333 1,1.917 true 1.594,3.896 1.542,4.271 true 1.781,3.896 1.844,4.271 true 0.99,4.271 1.219,3.896 true 1.281,4.271 1.406,3.885 true 2.156,3.885 2.354,4.26 true 2.094,4.281 1.969,3.896 true 2.333,3.896 2.542,4.25 true 0.271,1.208 0.583,1.406 0.313,0.198 10 false *b 0.375,2.292 0.688,2.49 0.313,0.198 10 false *c 2.271,4.302 2.583,4.5 0.313,0.198 10 false VR 0.198,3.031 0.51,3.229 0.313,0.198 10 false *a 2.031,4.313 2.344,4.51 0.313,0.198 10 false VL 1.781,4.313 2.094,4.51 0.313,0.198 10 false HL 1.458,4.313 1.771,4.51 0.313,0.198 10 false M+ 1.219,4.313 1.375,4.51 0.156,0.198 10 false E 0.917,4.313 1.073,4.51 0.156,0.198 10 false B 2.552,4.292 2.865,4.49 0.313,0.198 10 false HR
*a Component without harness connected
(Outer Mirror Switch Assembly)
*b Left/Right Select Switch
*c Mirror Adjust Switch


Check the mirror adjust switch.

i.

Select "L" on the left/right select switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for L position):
Tester Connection Switch Condition Specified Condition
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pushed Below 1 Ω
Not Pushed 10 kΩ or higher



iii.

Select "R" on the left/right select switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for R position):
Tester Connection Switch Condition Specified Condition
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pushed Below 1 Ω
Not Pushed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.
B344830C07
2.542,0.833 2.938,1.208 true 0.563,4.302 0.854,3.896 true 0.906,4.323 1.063,3.885 true 1.417,4.333 1.219,3.885 true 1.771,4.333 1.406,3.896 true 2.958,1.292 3.271,1.49 0.313,0.198 10 false *b 0.135,3 0.448,3.198 0.313,0.198 10 false *a 1.781,4.354 1.938,4.552 0.156,0.198 10 false E 1.406,4.354 1.563,4.552 0.156,0.198 10 false B 0.802,4.354 1.115,4.552 0.313,0.198 10 false MR 0.427,4.354 0.74,4.552 0.313,0.198 10 false MF
*a Component without harness connected
(Outer Mirror Switch Assembly)
*b Fold Away Switch


Check the fold away switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (MF) - 7 (E)
9 (MR) - 8 (B)
Pushed Below 1 Ω
10 (MF) - 8 (B)
9 (MR) - 7 (E)
Not Pushed Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retract Mirror)

a.
B344831C02
0.469,1.448 1.198,0.813 true 0.51,2.302 1,1.875 true 0.802,4.313 1.219,3.896 true 1.104,4.302 1.417,3.885 true 1.417,4.292 1.594,3.896 true 1.813,4.281 1.781,3.896 true 2.073,4.281 1.969,3.896 true 2.354,4.292 2.156,3.885 true 2.344,3.896 2.688,4.281 true 0.302,1.448 0.615,1.646 0.313,0.198 10 false *b 0.365,2.323 0.677,2.521 0.313,0.198 10 false *c 0.125,2.906 0.438,3.104 0.313,0.198 10 false *a 2.333,4.344 2.646,4.542 0.313,0.198 10 false VR 2.052,4.333 2.365,4.531 0.313,0.198 10 false VL 1.75,4.333 2.063,4.531 0.313,0.198 10 false HL 1.344,4.344 1.656,4.542 0.313,0.198 10 false M+ 1.052,4.344 1.208,4.542 0.156,0.198 10 false E 0.698,4.333 0.854,4.531 0.156,0.198 10 false B 2.656,4.333 2.969,4.531 0.313,0.198 10 false HR
*a Component without harness connected
(Outer Mirror Switch Assembly)
*b Left/Right Select Switch
*c Mirror Adjust Switch


Check the mirror adjust switch.

i.

Select "L" on the left/right select switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for L position):
Tester Connection Switch Condition Specified Condition
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pushed Below 1 Ω
Not Pushed 10 kΩ or higher



iii.

Select "R" on the left/right select switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for R position):
Tester Connection Switch Condition Specified Condition
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT Pushed Below 1 Ω
Not Pushed 10 kΩ or higher
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pushed Below 1 Ω
Not Pushed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.