Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017126 LIGHTING (EXT) _0092616 HEADLIGHT DIMMER SWITCH G

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  INSPECTION  


PROCEDURE

Hide 84140 1.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for TMMIN Made)

a.

Check the resistance.

i.

w/ Projector Headlight:

1.
E347964C01
0.417,1.833 0.865,1.427 true 0.833,1.833 1.25,1.406 true 1.167,1.833 1.417,1.406 true 2,1.833 1.875,1.417 true 2.917,1.833 2.583,1.417 true 2.583,1.833 2.417,1.417 true 1.958,1.083 1.667,0.417 true 2.219,1.083 2.5,0.417 true 2.26,1.833 2.135,1.417 true 0.365,1.865 0.521,2.063 0.156,0.198 10 false H 0.771,1.875 0.927,2.073 0.156,0.198 10 false T 1.042,1.875 1.354,2.073 0.313,0.198 10 false HF 1.958,1.875 2.271,2.073 0.313,0.198 10 false TL 2.865,1.875 3.177,2.073 0.313,0.198 10 false HU 2.542,1.875 2.854,2.073 0.313,0.198 10 false EL 2.573,0.333 3.031,0.531 0.458,0.198 10 false LFG 1.313,0.333 1.771,0.531 0.458,0.198 10 false BFG 2.219,1.875 2.531,2.073 0.313,0.198 10 false TR 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Light Control Switch
Tester Connection Switch Condition Specified Condition
12 (EL) - 18 (T) OFF 10 kΩ or higher
12 (EL) - 18 (T) TAIL Below 1 Ω
12 (EL) - 18 (T) HEAD Below 1 Ω
18 (T) - 20 (H) Below 1 Ω

Dimmer Switch
Tester Connection Switch Condition Specified Condition
12 (EL) - 17 (HF) HIGH FLASH Below 1 Ω
11 (HU) - 12 (EL) Below 1 Ω
11 (HU) - 12 (EL) HIGH Below 1 Ω

Turn Signal Switch
Tester Connection Switch Condition Specified Condition
12 (EL) - 13 (TR) OFF 10 kΩ or higher
12 (EL) - 15 (TL) 10 kΩ or higher
12 (EL) - 13 (TR) RH Below 1 Ω
12 (EL) - 15 (TL) LH Below 1 Ω

Front Fog Light Switch (w/ Fog Light)
Tester Connection Switch Condition Specified Condition
4 (BFG) - 3 (LFG) OFF 10 kΩ or higher
4 (BFG) - 3 (LFG) ON Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



ii.

w/o Projector Headlight:

1.
E218654C28
0.5,0.75 0.917,0.948 true 1.052,0.896 0.667,0.333 true 2.531,1.25 3,1.583 true 2.167,1.25 2.417,1.75 true 1.958,1.25 2.083,1.75 true 1.677,1.219 1.5,1.75 true 1.479,1.24 1.083,1.75 true 1.271,1.229 0.667,1.75 true 2.333,1.25 2.75,1.75 true 0.896,1.229 0.417,1.583 true 0.115,0.052 0.271,0.229 0.156,0.177 10 false *a 0.167,0.667 0.531,0.906 0.365,0.24 10 false LFG 0.323,0.25 0.75,0.5 0.427,0.25 10 false BFG 3.083,1.5 3.365,1.74 0.281,0.24 10 false TL 2.417,1.802 2.708,2.042 0.292,0.24 10 false E 2.042,1.802 2.385,2.063 0.344,0.26 10 false HL 1.396,1.802 1.708,2 0.313,0.198 10 false HU 0.969,1.792 1.26,2.083 0.292,0.292 10 false T1 0.542,1.781 0.854,2 0.313,0.219 10 false ED 2.698,1.802 3.01,2.083 0.313,0.281 10 false TR 0.135,1.51 0.417,1.75 0.281,0.24 10 false B1
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Light Control Switch
Tester Connection Switch Condition Specified Condition
10 (T1) - 11 (ED) OFF 10 kΩ or higher
10 (T1) - 11 (ED) TAIL Below 1 Ω
10 (T1) - 11 (ED) HEAD Below 1 Ω
13 (B1) - 11 (ED) Below 1 Ω

Dimmer Switch
Tester Connection Switch Condition Specified Condition
8 (HL) - 11 (ED) HIGH FLASH Below 1 Ω
9 (HU) - 11 (ED) Below 1 Ω
9 (HU) - 11 (ED) HIGH Below 1 Ω

Turn Signal Switch
Tester Connection Switch Condition Specified Condition
6 (TR) - 7 (E) OFF 10 kΩ or higher
5 (TL) - 7 (E) 10 kΩ or higher
6 (TR) - 7 (E) RH Below 1 Ω
5 (TL) - 7 (E) LH Below 1 Ω

Front Fog Light Switch (w/ Fog Light)
Tester Connection Switch Condition Specified Condition
3 (BFG) - 4 (LFG) OFF 10 kΩ or higher
3 (BFG) - 4 (LFG) ON Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.




Hide 84140 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for TMT Made)

a.

Check the resistance.

i.

for LHD:

1.
E380276C01
0.5,1.833 0.917,1.417 true 0.833,1.833 1.094,1.417 true 1.167,1.833 1.271,1.417 true 1.5,1.833 1.458,1.417 true 1.917,1.833 1.833,1.417 true 2.25,1.833 2,1.417 true 2.583,1.833 2.333,1.417 true 2.948,1.833 2.531,1.417 true 1.083,1.083 0.5,0.5 true 1.5,1.083 2.083,0.5 true 1.313,1.083 2.083,0.25 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.156,0.417 2.469,0.573 0.313,0.156 10 false B 2.156,0.167 2.573,0.333 0.417,0.167 10 false LFG 0.156,0.406 0.573,0.573 0.417,0.167 10 false BFG 0.458,1.844 0.875,2.01 0.417,0.167 10 false A 0.781,1.844 1.198,2.01 0.417,0.167 10 false H 1.135,1.844 1.552,2.01 0.417,0.167 10 false T 1.417,1.844 1.833,2.01 0.417,0.167 10 false HF 1.854,1.844 2.271,2.01 0.417,0.167 10 false EL 2.177,1.844 2.594,2.01 0.417,0.167 10 false HU 2.521,1.844 2.938,2.01 0.417,0.167 10 false TR 2.896,1.844 3.313,2.01 0.417,0.167 10 false TL
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Light Control Switch
Tester Connection Switch Condition Specified Condition
15 (EL) - 18 (T) OFF 10 kΩ or higher
15 (EL) - 20 (A) AUTO*1 Below 1 Ω
15 (EL) - 18 (T) TAIL Below 1 Ω
15 (EL) - 18 (T) HEAD Below 1 Ω
18 (T) - 19 (H) Below 1 Ω

Dimmer Switch
Tester Connection Switch Condition Specified Condition
15 (EL) - 17 (HF) HIGH FLASH Below 1 Ω
14 (HU) - 15 (EL) HIGH FLASH Below 1 Ω
14 (HU) - 15 (EL) HIGH Below 1 Ω

Turn Signal Switch
Tester Connection Switch Condition Specified Condition
15 (EL) - 12 (TR) OFF 10 kΩ or higher
15 (EL) - 11 (TL) 10 kΩ or higher
15 (EL) - 12 (TR) RH Below 1 Ω
15 (EL) - 11 (TL) LH Below 1 Ω

Front Fog Light Switch (w/ Fog Light)
Tester Connection Switch Condition Specified Condition
9 (BFG) - 8 (LFG) OFF 10 kΩ or higher
9 (BFG) - 8 (LFG) ON Below 1 Ω

Rear Fog Light Switch (w/ Rear Fog Light)
Tester Connection Switch Condition Specified Condition
8 (LFG) - 7 (B) OFF 10 kΩ or higher
8 (LFG) - 7 (B) ON Below 1 Ω


*1: w/ Automatic Light Control



If the result is not as specified, replace the headlight dimmer switch assembly.


ii.

for RHD:

1.
E375205C04
2.135,1.094 2.615,0.313 true 2.385,1.094 2.917,0.625 true 2.563,1.385 2.948,1.875 true 2.396,1.396 2.688,1.885 true 2.208,1.396 2.448,1.896 true 2.01,1.417 2.156,1.865 true 1.646,1.417 1.635,1.875 true 1.448,1.396 1.354,1.854 true 1.083,1.375 0.813,1.854 true 0.875,1.385 0.458,1.865 true 1.385,0.344 1.969,1.094 true 0.156,0.094 0.385,0.302 0.229,0.208 10 false *a 2.677,0.188 3.031,0.385 0.354,0.198 10 false LFG 2.969,0.521 3.323,0.719 0.354,0.198 10 false BFG 0.365,1.896 0.646,2.094 0.281,0.198 10 false TR 0.677,1.896 0.958,2.094 0.281,0.198 10 false TL 1.25,1.906 1.531,2.104 0.281,0.198 10 false HU 1.542,1.917 1.823,2.115 0.281,0.198 10 false EL 2.104,1.906 2.385,2.104 0.281,0.198 10 false HF 2.427,1.917 2.708,2.115 0.281,0.198 10 false T 2.677,1.917 2.958,2.115 0.281,0.198 10 false H 2.948,1.917 3.229,2.115 0.281,0.198 10 false A 1.219,0.25 1.573,0.448 0.354,0.198 10 false B
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Light Control Switch
Tester Connection Switch Condition Specified Condition
16 (EL) - 13 (T) OFF 10 kΩ or higher
16 (EL) - 11 (A) AUTO*1 Below 1 Ω
16 (EL) - 13 (T) TAIL Below 1 Ω
16 (EL) - 13 (T) HEAD Below 1 Ω
13 (T) - 12 (H) Below 1 Ω

Dimmer Switch
Tester Connection Switch Condition Specified Condition
16 (EL) - 14 (HF) HIGH FLASH Below 1 Ω
17 (HU) - 16 (EL) Below 1 Ω
17 (HU) - 16 (EL) HIGH Below 1 Ω

Turn Signal Switch
Tester Connection Switch Condition Specified Condition
20 (TR) - 16 (EL) OFF 10 kΩ or higher
19 (TL) - 16 (EL) 10 kΩ or higher
20 (TR) - 16 (EL) RH Below 1 Ω
19 (TL) - 16 (EL) LH Below 1 Ω

Front Fog Light Switch (w/ Fog Light)
Tester Connection Switch Condition Specified Condition
3 (LFG) - 2 (BFG) OFF 10 kΩ or higher
3 (LFG) - 2 (BFG) ON Below 1 Ω

Rear Fog Light Switch (w/ Rear Fog Light)
Tester Connection Switch Condition Specified Condition
3 (LFG) - 4 (B) OFF 10 kΩ or higher
3 (LFG) - 4 (B) ON Below 1 Ω


*1: w/ Automatic Light Control



If the result is not as specified, replace the headlight dimmer switch assembly.