Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PANEL(for TMMIN Made Manual Air Conditioning System) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0336794 AIR CONDITIONING PANEL(for TMMIN Made Manual Air Conditioning System) G

HEATING / AIR CONDITIONING  AIR CONDITIONING PANEL(for TMMIN Made Manual Air Conditioning System)  INSPECTION  


PROCEDURE

Hide 55900A 1.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY

a.

Check the resistance.

i.
I109787C02
1.188,3.479 0.833,3.479 true 2.25,3.469 2.583,3.469 true 1.604,3.552 1.844,3.021 true 2.229,3.854 2.406,4.135 true 1.031,4.135 1.188,3.844 true 2.625,3.375 2.938,3.573 0.313,0.198 10 false M1 2.385,4.208 2.698,4.406 0.313,0.198 10 false M2 1.896,2.927 2.208,3.125 0.313,0.198 10 false LO 0.667,3.406 0.979,3.604 0.313,0.198 10 false HI 0.969,4.208 1.281,4.406 0.313,0.198 10 false E 0.563,2.875 0.875,3.073 0.313,0.198 10 false *a 0.469,0.615 0.781,0.813 0.313,0.198 10 false *b 1.156,0.198 1.469,0.396 0.313,0.198 10 false *c 1.979,0.188 2.292,0.385 0.313,0.198 10 false *d 2.74,0.51 3.052,0.729 0.313,0.219 10 false *e 3.156,1.198 3.375,1.385 0.219,0.188 10 false *f
*a Component without harness connected
(Heater Control and Accessory Assembly)
*b Blower Switch OFF Position
*c Blower Switch LO Position
*d Blower Switch M1 Position
*e Blower Switch M2 Position
*f Blower Switch HI Position


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (LO), 5 (HI), 1 (M1), 6 (M2) - 10 (E) Blower switch: OFF 10 kΩ or higher
3 (LO) - 10 (E) Blower switch: LO Below 1 Ω
3 (LO), 1 (M1) - 10 (E) Blower switch: LO - M1 Below 1 Ω
3 (LO), 1 (M1) - 10 (E) Blower switch: M1 Below 1 Ω
3 (LO), 1 (M1), 6 (M2) - 10 (E) Blower switch: M1 - M2 Below 1 Ω
3 (LO), 6 (M2) - 10 (E) Blower switch: M2 Below 1 Ω
3 (LO), 6 (M2), 5 (HI) - 10 (E) Blower switch: M2 - HI Below 1 Ω
3 (LO), 5 (HI) - 10 (E) Blower switch: HI Below 1 Ω


If the result is not as specified, replace the heater control and accessory assembly.



b.

Check that the illumination lights.

i.
I109637C04
1.5,0.438 1.896,0.667 0.396,0.229 1.542,2.396 1.938,2.625 0.396,0.229 1.229,1.885 1.229,1.5 true 1.979,3.656 1.813,3.271 true 1.188,1.927 1.344,2.125 0.156,0.198 10 false E 1.927,3.708 2.344,3.865 0.417,0.156 10 false ILL+ 1.635,0.469 1.948,0.667 0.313,0.198 10 false A 1.688,2.438 2,2.635 0.313,0.198 10 false B 0.052,0.083 0.208,0.281 0.156,0.198 10 false *a
*a Component without harness connected
(Heater Control and Accessory Assembly)


Apply battery voltage to the heater control and accessory assembly and check that the heater control and accessory assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) →B-3 (ILL+)
Battery negative (-) → A-10 (E)
Illuminates


If the result is not as specified, replace the heater control and accessory assembly.



c.

Check the A/C switch.

i.

Measure the resistance according to the value(s) in the table below.

I110016C01
5.5,0.417 5.917,0.667 0.417,0.25 3.417,0.417 3.833,0.667 0.417,0.25 3.927,2.083 3.563,1.49 true 5.667,2.083 5.667,1.5 true 1.833,2.083 1.5,1.5 true 3.271,2.083 3.417,1.635 true 3.573,0.469 3.729,0.667 0.156,0.198 10 false A 5.667,0.469 5.823,0.667 0.156,0.198 10 false B 1.844,2.083 2,2.333 0.156,0.25 10 false *1 3.865,2.115 4.292,2.344 0.427,0.229 10 false LO 5.635,2.083 5.792,2.333 0.156,0.25 10 false B 2.573,0.188 3,0.417 0.427,0.229 10 false *a 3.156,2.115 3.583,2.344 0.427,0.229 10 false AC
*1 A/C switch - -
*a Component without harness connected
(Heater Control and Accessory Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (LO) - B-4 (B) A/C switch ON Below 1 Ω
A-3 (LO) - B-4 (B) A/C switch OFF 10 kΩ or higher


If the result is not as specified, replace the heater control and accessory assembly.



d.

Check that the A/C switch indicator.

i.

Connect the positive (+) lead from the battery to terminal A-9 (AC) and negative (-) lead to terminal B-4 (B).

OK:

Indicator lights up


If the result is not as specified, replace the heater control and accessory assembly.