Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2017.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"Power Steering (EPS)" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Power steering ECU assembly branch line or connector

·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly ground circuit

·

Power steering ECU assembly



WIRING DIAGRAM

E373381E08
3.25,1.083 3.75,0.167 3.75,0.167 3.917,0.167 true 4.781,1.083 4.948,0.667 4.948,0.667 5.115,0.667 true 1.188,5.021 5.167,5.219 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.198,5.406 5.177,5.604 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.302,5.01 7.156,5.26 2.854,0.25 10 false : CAN Branch Line (CANH) 4.302,5.406 7.156,5.656 2.854,0.25 10 false : CAN Branch Line (CANL) 0.115,0.146 2.969,0.396 2.854,0.25 12 false V Bus: 2.042,0.375 4.896,0.625 2.854,0.25 10 false DLC3 0.604,2.021 1.302,2.281 0.698,0.26 10 false 120 Ω 5.781,2.354 6.479,2.615 0.698,0.26 10 false F38 5.771,2.521 6.958,2.948 1.188,0.427 10 false Combination Meter Assembly 3.042,2.865 3.74,3.125 0.698,0.26 10 false F12 3.542,2.854 4.24,3.115 0.698,0.26 10 false F12 4.219,3.344 4.917,3.604 0.698,0.26 10 false F11 2.417,3.167 3.115,3.427 0.698,0.26 10 false F12 2.781,3.167 3.479,3.427 0.698,0.26 10 false IG 3,3.083 3.698,3.344 0.698,0.26 10 false CANL 3.5,3.083 4.198,3.344 0.698,0.26 10 false CANH 3.719,3.344 4.417,3.604 0.698,0.26 10 false PGND 4.292,3.167 4.99,3.427 0.698,0.26 10 false 2 3.708,2.635 4.406,2.896 0.698,0.26 10 false 7 3.198,2.625 3.896,2.885 0.698,0.26 10 false 8 2.51,2.969 3.208,3.229 0.698,0.26 10 false 1 1.75,3.333 2.448,3.594 0.698,0.26 10 false EPS-IG 2.563,4.052 4.552,4.313 1.99,0.26 10 false Power Steering ECU Assembly 4.146,2.531 6.135,2.792 1.99,0.26 10 false Trouble Area 0.281,2.365 2.271,2.625 1.99,0.26 10 false F130 0.271,2.552 0.969,2.813 0.698,0.26 10 false ECM 0.479,3.01 1.406,4.052 0.927,1.042 10 false from Ignition or Starter Switch Assembly*1 or IG1 Relay*2 5,3.229 6.844,3.604 1.844,0.375 10 false *1: w/o Smart Entry and Start System 5.021,3.865 6.813,4.24 1.792,0.375 10 false *2: w/ Smart Entry and Start System 3.969,0.083 4.583,0.281 0.615,0.198 10 false F62 5.177,0.583 5.792,0.781 0.615,0.198 10 false F174 3.958,0.24 6.073,0.417 2.115,0.177 10 false No. 1 CAN Junction Connector 5.167,0.729 7.156,0.969 1.99,0.24 10 false No. 23 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 11 seconds, and then drive the vehicle at a speed of 40 km/h (24 mph) or more for 300 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power steering ECU assembly connector.


c.
C328898C03
1.458,0.5 1.958,0.75 0.5,0.25 1.417,2.667 1.781,1.885 true 2.333,2.667 2,1.885 true 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 1.583,0.552 1.896,0.75 0.313,0.198 10 false F12 1.24,2.708 1.854,2.906 0.615,0.198 10 false CANH 2.156,2.708 2.771,2.906 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-7 (CANH) - F12-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the power steering ECU assembly connectors.


b.
C328899C05
1.469,0.333 1.969,0.583 0.5,0.25 1.469,2.167 1.969,2.417 0.5,0.25 2.5,1 2.042,1.302 true 1.406,3.188 0.948,3.49 true 0.177,0.146 0.49,0.302 0.313,0.156 10 false *a 1.604,0.385 2.063,0.583 0.458,0.198 10 false F11 1.604,2.219 2.063,2.417 0.458,0.198 10 false F12 2.563,0.938 3.177,1.135 0.615,0.198 10 false PGND 0.76,3.438 1.375,3.635 0.615,0.198 10 false IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F11-2 (PGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-1 (IG)- Body ground Ignition switch ON 11 to 14 V


Result:
Result
OK
NG




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)