Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0842  Transmission Fluid Pressure Sensor/Switch "A" Circuit Low  P0843  Transmission Fluid Pressure Sensor/Switch "A" Circuit High  


DESCRIPTION

The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0842 Transmission Fluid Pressure Sensor/Switch "A" Circuit Low When 2 seconds or more have elapsed after engine start, there is a short in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Oil pressure sensor

·

ECM


Does not come on DTC stored
P0843 Transmission Fluid Pressure Sensor/Switch "A" Circuit High When 2 seconds or more have elapsed after engine start, there is an open or a short to +B in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Oil pressure sensor

·

ECM


Does not come on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the oil pressure sensor. When there is an open or short circuit in the oil pressure sensor circuit, the ECM detects the problem and stores a DTC.

WIRING DIAGRAM

C318995E13
1.083,2.823 2.771,3.021 1.688,0.198 10 false Oil Pressure Sensor 5.323,3.073 6.135,3.438 0.813,0.365 10 false ECM 1.094,2.667 1.552,2.865 0.458,0.198 10 false B49 5.323,2.927 6.042,3.219 0.719,0.292 10 false F130 4.885,2.188 5.5,2.385 0.615,0.198 10 false EPTO 4.885,1.635 5.5,1.833 0.615,0.198 10 false PTO 4.885,1.146 5.5,1.344 0.615,0.198 10 false VCPT 2.156,1.24 2.771,1.438 0.615,0.198 10 false VC 2.073,1.729 2.688,1.927 0.615,0.198 10 false PTO 2.177,2.271 2.792,2.469 0.615,0.198 10 false E2 2.448,2.188 3.063,2.385 0.615,0.198 10 false 1 2.438,1.635 3.052,1.833 0.615,0.198 10 false 2 2.427,1.156 3.042,1.354 0.615,0.198 10 false 3 4.635,1.135 4.896,1.406 0.26,0.271 10 false 32 4.635,1.615 4.896,1.885 0.26,0.271 10 false 24 4.635,2.188 4.854,2.417 0.219,0.229 10 false 31 5.583,0.979 6.198,1.177 0.615,0.198 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be performed after checking and confirming that the engine is normal.

·

Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).

·

Perform this test with the air conditioning off.

·

Do not perform the stall speed test for longer than 5 seconds.

·

When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
A/T Oil Pressure
50004 234 13 409

g.

Observe "A/T Oil Pressure" in the Data List.


h.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

4.2 to 4.9 MPa (42.8 to 50.0 kgf/cm2, 609 to 711 psi): D position stall test

·

4.0 to 5.1 MPa (40.8 to 52.0 kgf/cm2, 580 to 740 psi): R position stall test


-

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)

B

5.REPLACE ECM
2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)
a.

Disconnect the B49 oil pressure sensor connector.


b.

Disconnect the F130 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B49-1 (E2) - F130-31 (EPTO) Always Below 1 Ω
B49-2 (PTO) - F130-24 (PTO) Always Below 1 Ω
B49-3 (VC) - F130-32 (VCPT) Always Below 1 Ω
B49-1 (E2) or F130-31 (EPTO) - Body ground and other terminals Always 10 kΩ or higher
B49-2 (PTO) or F130-24 (PTO) - Body ground and other terminals Always 10 kΩ or higher
B49-3 (VC) or F130-32 (VCPT) - Body ground and other terminals Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-24 (PTO) - Body ground Ignition switch ON Below 1 V
B49-2 (PTO) - Body ground Ignition switch ON Below 1 V



e.

Connect the F130 ECM connector.


f.

Connect the B49 oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (VCPT TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (VCPT TERMINAL VOLTAGE)
a.
C125747C41
0.396,0.969 0.896,1.219 0.5,0.25 1.042,1.667 1.458,1.25 true 2.552,1.708 2.042,1.26 true 0.833,1.583 1.219,1.792 0.385,0.208 10 false E2 2.604,1.615 2.875,1.802 0.271,0.188 10 false VC 0.094,0.094 0.313,0.25 0.219,0.156 10 false *a 0.51,1.01 0.948,1.188 0.438,0.177 10 false B49
*a Front view of wire harness connector
(to Oil Pressure Sensor)


Disconnect the oil pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B49-3 (VC) - B49-1 (E2) Ignition switch ON 4.75 to 5.25 V



c.

Connect the oil pressure sensor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE OIL PRESSURE SENSOR

NG

5.REPLACE ECM
4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K312 CVT>OIL PRESSURE SENSOR>COMPONENTS


Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT