Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for Separate Seat Type) › from 2018.01
RM30M0E _58 Vehicle Interior _017116 SEAT _0092020 REAR SEAT ASSEMBLY(for Separate Seat Type) A

SEAT  REAR SEAT ASSEMBLY(for Separate Seat Type)  REASSEMBLY  


PROCEDURE

Hide 71078S 1.INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (for LH Side)

a.

w/o Armrest:

i.
B351896C01
1.573,4.302 1.635,4.177 false 0.615,2.885 0.417,2.802 false 0.25,2.719 0.563,2.917 0.313,0.198 10 false *1 1.49,4.313 1.802,4.51 0.313,0.198 10 false *a
*1 Hog Ring
*a Hog Ring Pliers


Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 8 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.

·

Align the center of the hog ring installation area of the separate type rear seatback cover LH with the center of the separate type rear seatback pad LH so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.





b.

w/ Armrest:

i.
B351894C01
0.458,2.76 0.615,2.896 false 1.656,4.177 1.604,4.333 false 0.302,2.656 0.615,2.854 0.313,0.198 10 false *1 1.521,4.344 1.833,4.542 0.313,0.198 10 false *a
*1 Hog Ring
*a Hog Ring Pliers


Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 16 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover LH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.

·

Align the center of the hog ring installation area of the separate type rear seatback cover LH with the center of the separate type rear seatback pad LH so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.





Hide 71077S 2.INSTALL SEPARATE TYPE REAR SEATBACK COVER RH (for RH Side)

a.
B344600C01
0.563,2.906 0.396,2.74 false 1.792,4.208 1.604,4.396 false 0.25,2.625 0.563,2.781 0.313,0.156 10 false *1 1.531,4.417 1.844,4.573 0.313,0.156 10 false *a
*1 Hog Ring
*a Hog Ring Pliers


Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 8 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover RH.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.

·

Align the center of the hog ring installation area of the separate type rear seatback cover RH with the center of the separate type rear seatback pad RH so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.




Hide 3.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD LH (for LH Side)

a.

Temporarily install the separate type rear seatback cover with pad LH to the rear seatback frame sub-assembly LH.


b.
B344594C02
0.406,0.583 0.427,0.802 false 1.438,0.281 1.396,0.49 false 2.156,0.615 2.188,0.854 false 3,1.229 3.031,1.438 false 0.354,0.802 0.667,0.958 0.313,0.156 10 false *a 1.313,0.5 1.625,0.656 0.313,0.156 10 false *a 2.125,0.844 2.438,1 0.313,0.156 10 false *a 2.958,1.438 3.271,1.594 0.313,0.156 10 false *a
*a Protruding


Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame sub-assembly LH.


c.

Engage the 8 claws to install the 4 rear seat headrest supports.


d.
B361092C01
0.24,1.656 0.552,1.854 0.313,0.198 10 false *a 1.458,2.896 1.771,3.094 0.313,0.198 10 false *b
*a Zipper
*b Hook


Fasten the zipper to engage the hook.


Hide 4.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD RH (for RH Side)

a.

Temporarily install the separate type rear seatback cover with pad RH to the rear seatback frame sub-assembly RH.


b.
B344602C01
1.438,0.313 1.458,0.646 false 2.896,0.344 2.875,0.677 false 1.396,0.646 1.708,0.802 0.313,0.156 10 false *a 2.813,0.698 3.125,0.854 0.313,0.156 10 false *a
*a Protruding


Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame sub-assembly RH.


c.

Engage the 4 claws to install the 2 rear seat headrest supports.


d.
B361093C01
2.719,1.719 3.031,1.917 0.313,0.198 10 false *a 1.563,2.875 1.875,3.073 0.313,0.198 10 false *b
*a Zipper
*b Hook


Fasten the zipper to engage the hook.


Hide 73344 5.INSTALL REAR SEAT SHOULDER BELT GUIDE LH (for Sedan LH Side)

HINT:

Use the same procedure for both sides.


a.
B356491

Engage the guide to install the rear seat shoulder belt guide LH.


b.

Install the 2 screws.


Hide 73343 6.INSTALL REAR SEAT SHOULDER BELT GUIDE RH (for Sedan RH Side)

a.
B356478

Engage the guide to install the rear seat shoulder belt guide RH.


b.

Install the 2 screws.


Hide 66990 7.INSTALL CUP HOLDER ASSEMBLY (w/ Armrest)

a.
B344588

Engage the 4 guides to install the cup holder assembly.


Hide 72830 8.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Armrest)

a.

Install the bush to the rear seat center armrest assembly.


b.
B356492

Engage the guide to install the rear seat center armrest assembly.


c.

Install the bush, wave washer and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72868B 9.INSTALL CENTER ARMREST HINGE COVER (w/ Armrest)

a.
B344586

Engage the claw and 2 guides to install the center armrest hinge cover.


Hide 71960B 10.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (for LH Side)

a.

Install the rear seat center headrest assembly.


Hide 71940A 11.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the 2 rear seat headrest assemblies.


Hide 71075B 12.INSTALL BENCH TYPE REAR SEAT CUSHION COVER