ECM
The standard voltage and resistance of each pair of ECM terminals is shown in the table below.
The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage or resistance for that pair of terminals shown in the "Specified Condition" column.
Use the illustration above as a reference for the ECM terminals.
| Terminal No.(Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F131-3 (BATT) - B46-3 (E1) | G - W-B | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| F131-1 (+B) - B46-3 (E1) | R - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| F131-2 (+B2) - B46-3 (E1) | R - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| F130-13 (CANH) - B46-3 (E1) | BE - W-B | CAN communication line | Ignition switch ON | Pulse generation |
| B47-15 (NSW) - B46-3 (E1) | W - W-B | Park/neutral position switch signal | Ignition switch ON and shift lever in P or N | Below 1 V |
| Ignition switch ON and shift lever not in P or N | 11 to 14 V | |||
| F130-14 (CANL) - B46-3 (E1) | W - W-B | CAN communication line | Ignition switch ON | Pulse generation |
| F130-6 (MREL) - B46-3 (E1) | L - W-B | EFI relay | Ignition switch ON | 11 to 14 V |
| B48-30 (S) - B46-3 (E1) | V - W-B | M position switch signal | Ignition switch ON and shift lever in M | 11 to 14 V |
| Ignition switch ON and shift lever in any position except M | Below 1 V | |||
| B48-17 (SFTU) - B46-3 (E1) | R - W-B | Up shift position switch signal | Ignition switch ON and shift lever in M | 11 to 14 V |
| Ignition switch ON and shift lever held in "+" (Up shift)
Ignition switch ON and "+" shift paddle switch operated* |
Below 1 V | |||
| B48-27 (SFTD) - B46-3 (E1) | L - W-B | Down shift position switch signal | Ignition switch ON and shift lever in M | 11 to 14 V |
| Ignition switch ON and shift lever held in "-" (Down shift)
Ignition switch ON and "-" shift paddle switch operated* |
Below 1 V | |||
| B46-5 (+BM) - B46-3 (E1) | R - W-B | Power source of throttle actuator | Always | 11 to 14 V |
| B48-7 (SLP+) - B48-6 (SLP-) | G - LG | Shift solenoid valve SLP signal | Engine idling | Pulse generation |
| B48-11 (SC) - B46-3 (E1) | BE - W-B | Shift solenoid valve SC signal | ·
For 1 second after moving shift lever from P to D or R, or N to D or R ·
Lock-up ON to OFF |
Pulse generation |
| B48-2 (SLU+) - B48-1 (SLU-) | SB - GR | Shift solenoid valve SLU signal | Lock-up turned from OFF to ON | Pulse generation |
| B48-5 (SLS+) - B48-4 (SLS-) | V - BE | Shift solenoid valve SLS signal | Engine idling | Pulse generation |
| B46-3 (E1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| F130-8 (R) - B46-3 (E1) | GR - W-B | R position switch signal | Ignition switch ON and shift lever in R | 11 to 14 V |
| Ignition switch ON and shift lever not in R | Below 1 V | |||
| F130-18 (D) - B46-3 (E1) | L - W-B | D position switch signal | Ignition switch ON and shift lever in D | 11 to 14 V |
| Ignition switch ON and shift lever not in D | Below 1 V | |||
| B47-12 (SL) - B46-3 (E1) | W - W-B | Shift solenoid valve SL signal | Lock-up operating | Pulse generation |
| B48-24 (N) - B46-3 (E1) | B - W-B | N position switch signal | Ignition switch ON and shift lever in N | 11 to 14 V |
| Ignition switch ON and shift lever not in N | Below 1 V | |||
| B48-25 (P) - B46-3 (E1) | P - W-B | P position switch signal | Ignition switch ON and shift lever in P | 11 to 14 V |
| Ignition switch ON and shift lever not in P | Below 1 V | |||
| F130-24 (PTO) - F130-31 (EPTO) | L - BE | Oil pressure sensor signal | Engine idling with shift lever in P | 0.8 to 1.2 V |
| F130-32 (VCPT) - F130-31 (EPTO) | V - BE | Power supply for oil pressure sensor | Ignition switch ON | 4.75 to 5.25 V |
| B48-32 (NIN+) - B48-31 (NIN-) | Y - LG | Transmission revolution sensor (NIN) signal | When driving with shift lever in D | Pulse generation |
| B48-19 (NTO) - B46-3 (E1) | G - W-B | Transmission revolution sensor (NT) signal | When driving with shift lever in D | Pulse generation |
| B48-29 (NTB) - B46-3 (E1) | BR - W-B | Power supply for transmission revolution sensor (NT) | Ignition switch ON | 11 to 14 V |
| B47-9 (NOTO) - B46-3 (E1) | L - W-B | Transmission revolution sensor (NOUT) signal | When driving with shift lever in D | Pulse generation |
| B47-10 (NOTB) - B46-3 (E1) | G - W-B | Power supply for transmission revolution sensor (NOUT) | Ignition switch ON | 11 to 14 V |
| B48-20 (THO1) - B48-21 (ETHO) | Y - B | CVT fluid temperature sensor signal | CVT fluid temperature: 60 to 120°C (140 to 248°F) | 0.2 to 1.0 V |
*: w/ Shift Paddle Switch