Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › from 2018.01
RM30M0E _59 Vehicle Exterior _017125 WIPER / WASHER _0090076 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.


c.

Apply MP grease to the pivot of the windshield wiper motor assembly.


d.
B348547C01
2.146,1.052 2.563,0.635 true 1.5,0.823 1.479,0.292 true 2.604,0.531 2.917,0.688 0.313,0.156 10 false *1 1.406,0.115 1.719,0.271 0.313,0.156 10 false *a
*1 Wiper Rod
*a Pivot of the windshield wiper motor assembly


Connect the wiper rod to the pivot of the windshield wiper motor assembly.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
B348548C01
1.875,0.333 2.167,0.771 true 1.719,0.219 2.031,0.375 0.313,0.156 10 false *1
*1 Motor Grommet


Slide the windshield wiper motor and link assembly as shown in the illustration and engage the motor grommet with the body.

NOTICE:

Be careful not to damage the windshield glass when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


d.

Engage the clamp.


Hide 55781E 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 8 guides and 5 claws to install the cowl top ventilator louver sub-assembly.


b.

Install the 2 clips.


Hide 53867 4.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.

Engage the 3 guides and 2 pins to install the front fender to cowl side seal LH.


Hide 53866 5.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E226523C15
1.052,1.125 0.229,1.125 true 0.073,1.031 0.427,1.281 0.354,0.25 10 false *a
*a Wiper Arm Serration


When reusing the front wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.
E231343C15
1.958,1.104 2.26,1.104 true 2.292,0.99 2.604,1.229 0.313,0.24 10 false *a
*a Wiper Pivot Serration


When reusing the wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.

NOTICE:

Do not grind down the wiper pivot serrations.




c.

Operate the wiper, and then stop the windshield wiper motor assembly in the automatic stop position.


d.
B347413C01
1.26,1.698 1.042,1.344 true 0.865,1.24 1.177,1.396 0.313,0.156 10 false *a
*a Ceramic Dot


Align the blade tip with the ceramic dot on the glass, as shown in the illustration.

HINT:

Hold the wiper arm by hand while tightening the nut.



e.

Install the nut on the front wiper arm and blade assembly LH.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E226523C15
1.052,1.125 0.229,1.125 true 0.073,1.031 0.427,1.281 0.354,0.25 10 false *a
*a Wiper Arm Serration


When reusing the front wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.
E231343C15
1.958,1.104 2.26,1.104 true 2.292,0.99 2.604,1.229 0.313,0.24 10 false *a
*a Wiper Pivot Serration


When reusing the wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.

NOTICE:

Do not grind down the wiper pivot serrations.




c.

Operate the wiper, and then stop the windshield wiper motor assembly in the automatic stop position.


d.
B347412C01
1.24,1.708 1.646,1.469 true 1.667,1.354 1.979,1.51 0.313,0.156 10 false *a
*a Ceramic Dot


Align the blade tip with the ceramic dot on the glass, as shown in the illustration.

HINT:

Hold the wiper arm by hand while tightening the nut.



e.

Install the nut on the front wiper arm and blade assembly RH.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 8.INSTALL FRONT WIPER ARM HEAD CAP

HINT:

Use the same procedure for both sides.


a.
B347414

Engage the 3 claws to install the front wiper arm head cap.