Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2018.01
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM U

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

·

Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.


Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
600 to 700 rpm: Idling When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
MAF Airflow rate from mass air flow meter Min.: 0 gm/sec.
Max.: 655.35 gm/sec.
·

1.0 to 3.0 gm/sec: Idling with warm engine (A/C off and shift lever in N)

·

3.0 to 9.0 gm/sec: 3000 rpm (A/C off and shift lever in N)


This is the intake air amount from the mass air flow meter.
Coolant Temp Engine coolant temperature Min.: -40°C (-40°F)
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up This is the engine coolant temperature.
HINT:
·

After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

·

If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.

·

Check if the engine overheats when the value indicates 140°C (284°F).



Throttle Motor DUTY Throttle actuator Min.: 0%
Max.: 100%
10 to 22%: Idling(A/C off and shift lever in N) This is the out put duty ratio of the throttle actuator drive circuit.
N Range Status Judgment for shift lever N position ON or OFF
·

OFF: Shift lever not in N

·

ON: Shift lever in N


-
Starter Signal Starter signal OFF or ON
·

ON: Starter operating

·

OFF: Starter not operating


-
Neutral Position SW Signal Park/neutral position switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Stop Light Switch Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
A/C Signal A/C switch status OFF or ON ON: A/C switch on w/ Air Conditioning System
Closed Throttle Position SW Closed throttle position switch status OFF or ON
·

ON: Throttle fully closed

·

OFF: Throttle open


-
TC and TE1 TC and CG (TE1) terminals of DLC3 OFF or ON - -
SPD (NT) Input turbine speed Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up on (After warming up engine): Input turbine speed (NT) equal to engine speed

·

Lock-up off (Idling with shift lever in P or N): Input turbine speed (NT) nearly equal to engine speed

·

Vehicle stopped with shift lever in R: 0 rpm


Data is displayed in increments of 50 rpm.
Shift SW Status (P Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


Shift SW Status (R Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


Shift SW Status (N Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
HINT:

If the same malfunction occurs even after adjusting these parts, refer to DTC P0705*1.


Shift SW Status (N,P Range) Supported Status of Park/neutral position switch (N or P) support Supp or Unsupp - -
Shift SW Status (N,P Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


-
Sports Shift Up SW Sport shift up switch status OFF or ON
·

ON: Shift lever held in "+"

·

OFF: Shift lever not held in "+"


-
Sports Shift Down SW Sport shift down switch status OFF or ON
·

ON: Shift lever held in "-"

·

OFF: Shift lever not held in "-"


-
Sports Mode Selection SW Transmission control switch status OFF or ON
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Shift SW Status (D Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in D or M

·

OFF: Shift lever not in D or M


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
A/T Oil Temperature 1 CVT fluid temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall speed test: Approximately 100°C (212°F)

·

Equal to ambient temperature after cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or higher, the CVT fluid temperature sensor circuit is open or shorted.
ATF Thermal Degradation Estimate Estimated value of ATF thermal degradation Min.: 0
Max.: 65535
- If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the CVT fluid is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the CVT fluid.
NT Sensor Voltage Input turbine speed (NT) sensor output voltage Min.: 0 V
Max.: 4.999 V
Engine idling (Vehicle stopped with shift lever in P or N): 0.6 to 1.5 V -
SPD (NIN) Primary pulley speed (NIN) Min.: 0 rpm
Max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed


Data is displayed in increments of 50 rpm.
SPD (NOUT) Secondary pulley speed (NOUT) Min.: 0 rpm
Max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Vehicle cruising at approximately 60 km/h (37 mph): 2975 rpm


Data is displayed in increments of 50 rpm.
NOUT Sensor Voltage Secondary pulley speed (NOUT) sensor output voltage Min.: 0.000 V
Max.: 4.999 V
Engine idling: Approximately 2 V -
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection
·

D position stall speed test: 4.4 to 6.5 MPa

·

R position stall speed test: 4.4 to 6.8 MPa


-
G Sensor Converted output voltage of deceleration sensor Min.: 0 V
Max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-
Lock Up Lock-up ON or OFF
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
Shift Status ECM gearshift command 1st, 2nd, 3rd, 4th or 5th Same as actual gear *2
Solenoid (DS2) Shift solenoid valve DS2 status ON or OFF
·

OFF: Constant cruising with shift lever in D

·

ON: Accelerator pedal depressed further after cruising with shift lever in D


-
Solenoid (DS1) Shift solenoid valve DS1 status ON or OFF
·

ON: Driving with shift lever in D and accelerator pedal depressed

·

OFF: Accelerator pedal released when driving with shift lever in D with accelerator pedal depressed


-
Solenoid (SLS) Shift solenoid valve SLS status ON or OFF
·

ON: After engine start

·

OFF: Ignition switch ON


-
SLT Solenoid Status Shift solenoid valve SLT status ON or OFF
·

ON: After engine start

·

OFF: Ignition switch ON


-
SLU Solenoid Status Shift solenoid valve SLU status ON or OFF
·

ON: Lock up operating

·

OFF: Lock up not operating


-
G Sensor Calibration G sensor calibration status Incomplete or Complete Complete -
G Sensor Learning Value G sensor learned value voltage Min.: 0 V
Max.: 79.998 V
G sensor calibration is complete: 2.31 V to 2.69 V -
CVT Oil Press Calibration CVT oil pressure calibration status Incomplete or Complete Complete -
HINT:
·

*2: "Shift Status" is a signal divided into 5 gear positions for Active Test.

It does not express gear ratios for normal driving or gear positions for 7-speed sport sequential shiftmatic mode.





ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

In accordance with the display on the GTS, perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Connect the TC and TE1 Turn on and off TC and TE1 connection ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


[Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P.
Activate the Solenoid (SLU) Operate shift solenoid valve SLU ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.
Activate the Solenoid (SLT) Operate shift solenoid valve SLT ON or OFF [Vehicle Condition]
Perform with the ignition switch ON and the engine running.
Activate the Lock Up Operate lock-up ON or OFF Possible to check lock-up operation.
HINT:

Perform "Activate the Lock Up" while monitoring the engine speed (ESPD) and turbine speed (NT).


[Vehicle Condition]
Perform at a vehicle speed of 60 km/h (37 mph) or more.
Control the Shift Position Operate the shift solenoid valves to allow the gear ratio to be manually selected [1st (gear ratio max.) - 2nd - 3rd - 4th - 5th (gear ratio min.)]
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Used to check the operation of the shift solenoid valves.
HINT:

Perform "Control the Shift Position" while monitoring "Shift Status" to confirm actual gear position.


NOTICE:

Performing this test at speeds other than those specified in "Vehicle Condition" will damage the transaxle.


[Vehicle Condition]
Perform at a vehicle speed of 20 km/h (12 mph) or more and 45 km/h (28 mph) or less.
Activate the Solenoid (DS1) Operate shift solenoid valve DS1 ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.
Activate the Solenoid (DS2) Operate shift solenoid valve DS2 ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.
Control the SLS Pressure Operate shift solenoid valve SLS High or Low [Vehicle Condition]
Perform with the ignition switch ON and the engine running.
Activate the Solenoid (SLS) Operate shift solenoid valve SLS ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.