Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE(for Sedan) › from 2018.01
RM30M0E _59 Vehicle Exterior _017128 EXTERIOR PANELS / TRIM _0092436 NAME PLATE(for Sedan) A

EXTERIOR PANELS / TRIM  NAME PLATE(for Sedan)  INSTALLATION  


PROCEDURE

Hide 75441A 1.INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE (w/ Brand Name Plate)

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature:
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)


CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 1 luggage compartment door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 1 luggage compartment door name plate as shown in the illustration.

B493480C01
4.656,2.844 5.073,2.427 false 4.469,2.75 4.781,2.906 0.313,0.156 10 false *1 4.25,1.656 4.458,1.865 0.208,0.208 10 false A 4.542,0.958 4.75,1.167 0.208,0.208 10 false B 5.948,1.865 6.156,2.073 0.208,0.208 10 false C
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 38.8 mm (1.528 in.) B 22.3 mm (0.878 in.)
C 63.4 mm (2.496 in.) - -


NOTICE:

Install the No. 1 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 1 luggage compartment door name plate to 20 to 30°C(68 to 86°F) and install the No. 1 luggage compartment door name plate.



Hide 75444 2.INSTALL NO. 4 LUGGAGE COMPARTMENT DOOR PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 4 luggage compartment door plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

for Type A:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B503160C01
6.063,1.479 6.427,1.479 false 6.156,3.281 6.521,3.281 false 6.104,5.188 6.469,5.188 false 4.365,0.198 4.677,0.417 0.313,0.219 12 false *A 4.354,1.948 4.667,2.188 0.313,0.24 12 false *B 4.365,3.917 4.688,4.177 0.323,0.26 12 false *C 6.51,1.385 6.792,1.604 0.281,0.219 10 false *1 6.615,3.177 6.896,3.396 0.281,0.219 10 false *1 6.521,5.094 6.802,5.313 0.281,0.219 10 false *1 6.375,0.208 6.531,0.365 0.156,0.156 10 false C 5.417,0.875 5.573,1.031 0.156,0.156 10 false B 6.052,0.844 6.208,1 0.156,0.156 10 false A 6.365,2.229 6.521,2.385 0.156,0.156 10 false F 5.417,2.844 5.573,3 0.156,0.156 10 false E 6.073,2.75 6.229,2.906 0.156,0.156 10 false D 6.458,4.042 6.615,4.198 0.156,0.156 10 false I 5.729,4.75 5.938,4.948 0.208,0.198 10 false H 6.771,4.583 6.979,4.781 0.208,0.198 10 false G
*A w/o Brand Name Plate *B w/ Brand Name Plate
*C w/ Engine Displacement Mark - -
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 84.9 mm (3.343 in.) B 65.7 mm (2.587 in.)
C 71.0 mm (2.795 in.) D 56.9 mm (2.240 in.)
E 37.8 mm (1.488 in.) F 52.7 mm (2.075 in.)
G 38.3 mm (1.508 in.) H 37.7 mm (1.484 in.)
I 22.0 mm (0.866 in.) - -


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




c.

for Type B:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B503161C01
6.167,1.396 6.531,1.396 false 6.125,3.188 6.49,3.188 false 6.146,5.156 6.51,5.156 false 4.281,0.208 4.594,0.427 0.313,0.219 12 false *A 4.313,1.917 4.635,2.188 0.323,0.271 12 false *B 4.354,3.938 4.698,4.229 0.344,0.292 12 false *C 6.615,1.313 6.927,1.469 0.313,0.156 10 false *1 6.552,3.094 6.865,3.25 0.313,0.156 10 false *1 6.594,5.063 6.906,5.219 0.313,0.156 10 false *1 6.344,0.198 6.656,0.354 0.313,0.156 10 false C 5.448,0.885 5.625,1.063 0.177,0.177 10 false B 6.052,0.802 6.208,0.979 0.156,0.177 10 false A 6.344,2.104 6.656,2.26 0.313,0.156 10 false F 6.073,2.646 6.26,2.823 0.188,0.177 10 false D 5.427,2.719 5.615,2.896 0.188,0.177 10 false E 6.469,4.063 6.583,4.25 0.115,0.188 10 false I 5.729,4.729 5.917,4.906 0.188,0.177 10 false H 6.781,4.563 6.969,4.74 0.188,0.177 10 false G
*A w/o Brand Name Plate *B w/ Brand Name Plate
*C w/ Engine Displacement Mark - -
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 84.7 mm (3.334 in.) B 65.3 mm (2.570 in.)
C 70.6 mm (2.779 in.) D 56.8 mm (2.236 in.)
E 37.4 mm (1.472 in.) F 52.3 mm (2.059 in.)
G 37.6 mm (1.480 in.) H 37.3 mm (1.469 in.)
I 21.6 mm (0.850 in.) - -


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




d.

for Type C:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B503162C01
6.177,1.448 6.531,1.448 false 6.188,3.177 6.542,3.177 false 4.365,0.219 4.698,0.438 0.333,0.219 12 false *A 6.594,1.365 6.906,1.521 0.313,0.156 10 false *1 4.292,2 4.625,2.219 0.333,0.219 12 false *B 6.615,3.073 6.927,3.229 0.313,0.156 10 false *1 6.365,0.208 6.677,0.365 0.313,0.156 10 false C 5.448,0.938 5.635,1.104 0.188,0.167 10 false B 6.063,0.865 6.25,1.031 0.188,0.167 10 false A 6.448,2.083 6.635,2.25 0.188,0.167 10 false F 5.708,2.802 5.896,2.969 0.188,0.167 10 false E 6.75,2.656 6.938,2.823 0.188,0.167 10 false D
*A w/o Engine Displacement Mark *B w/ Engine Displacement Mark
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 60.4 mm (2.378 in.) B 41.4 mm (1.630 in.)
C 57.2 mm (2.252 in.) D 45.9 mm (1.807 in.)
E 41.4 mm (1.630 in.) F 26.4 mm (1.039 in.)


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




Hide 75444 3.INSTALL NO. 3 LUGGAGE COMPARTMENT DOOR NAME PLATE (w/ Engine Displacement Mark)

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 3 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 3 back door name plate as shown in the illustration.

B503163C01
6.823,1.823 6.74,1.438 false 6.885,1.74 7.094,1.906 0.208,0.167 10 false *1 6.229,1.375 6.438,1.542 0.208,0.167 10 false B 5.417,1.938 5.625,2.104 0.208,0.167 10 false A 6.135,1.865 6.344,2.031 0.208,0.167 10 false C
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 37.7 mm (1.484 in.) B 73.1 mm (2.878 in.)
C 55.5 mm (2.185 in.) - -


NOTICE:

Install the No. 3 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 3 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 3 back door name plate.



Hide 75442 4.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

w/ Brand Name Plate

i.

Install a new No. 2 luggage compartment door name plate as shown in the illustration.

B493479C01
6.083,2.542 6.5,2.958 false 6.573,2.865 6.885,3.021 0.313,0.156 10 false *1 5.125,1.979 5.292,2.146 0.167,0.167 10 false A 6.885,1.656 7.052,1.823 0.167,0.167 10 false C 6.583,1.073 6.75,1.24 0.167,0.167 10 false B
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 70.4mm (2.772 in.) B 15.3 mm (0.602 in.)
C 28.7mm (1.130 in.) - -


NOTICE:

Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.




c.

w/o Brand Name Plate

i.

Install a new No. 2 luggage compartment door name plate as shown in the illustration.

B484327C01
4.354,2.531 4.573,2.292 false 3.896,1.76 4.052,1.958 0.156,0.198 10 false A 4.271,1.219 4.427,1.417 0.156,0.198 10 false B 6.01,2.031 6.167,2.229 0.156,0.198 10 false C 4.177,2.458 4.396,2.656 0.219,0.198 10 false *1
*1 Luggage Compartment Door Panel - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 39.4 mm (1.551 in.) B 21.3 mm (0.838 in.)
C 87.3 mm (3.437 in.) - -


NOTICE:

Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.




Hide 75431 5.INSTALL LUGGAGE COMPARTMENT DOOR EMBLEM

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

Heating Temperature
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)

CAUTION:

Do not burn yourself on the hot body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the remaining double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

NOTICE:

Installing the symbol emblem with any double-sided tape remaining on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B484298C01
0.427,3.552 0.74,3.552 true 2.583,3.802 2.896,3.802 true 0.25,3.458 0.563,3.656 0.313,0.198 10 false *a 2.969,3.729 3.281,3.927 0.313,0.198 10 false *a
*a Location Pin


Insert the 2 pins into the back door panel and install a new luggage compartment door emblem.

NOTICE:

Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.