Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE(for Front Door) › from 2018.01
RM30M0E _59 Vehicle Exterior _017128 EXTERIOR PANELS / TRIM _0092446 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the attachment surface.

i.

Using an infrared light, heat the vehicle body surface.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

NOTICE:

Do not heat the vehicle body excessively.



ii.

Clean off any tape adhesive residue with cleaner.



b.

Installation temperature

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using an infrared light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape becomes stiff and comes off easily. When the temperature is high, the tape elasticity increases.





c.

Before installation

i.

Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

NOTICE:

Do not bend the tape or leave it in high temperature places.




e.

Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

NOTICE:
·

Position the tape accurately to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body prematurely. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.

B348879C03
0.167,0.167 2.833,1.583 2.667,1.417 0.677,0.583 0.917,0.5 false 2.229,0.75 2.417,0.583 false 1.333,1.333 1.583,1.208 false 1.865,2.417 2.104,2.333 false 1.5,3 1.833,3.125 false 2.115,3.417 2.583,3.417 true 4.583,2.75 4.917,2.75 true 5.635,3.417 6,3.417 true 4.833,3.167 5.208,3.167 false 0.208,0.198 0.521,0.396 0.313,0.198 10 false *c 0.938,0.375 1.25,0.573 0.313,0.198 10 false *a 2.417,0.417 2.729,0.615 0.313,0.198 10 false *d 1.188,1.302 1.5,1.5 0.313,0.198 10 false *e 0.604,1.667 1.01,1.99 0.406,0.323 12 false *A 1.073,2.24 1.385,2.438 0.313,0.198 10 false *f 2,1.813 2.313,2.01 0.313,0.198 10 false *g 1.698,2.344 2.01,2.542 0.313,0.198 10 false *a 1.333,2.896 1.646,3.094 0.313,0.198 10 false *1 2.635,3.323 2.948,3.521 0.313,0.198 10 false *b 2.792,2.583 3.104,2.781 0.313,0.198 10 false *i 4.583,2.25 4.896,2.448 0.313,0.198 10 false *f 4.427,2.656 4.74,2.854 0.313,0.198 10 false *a 5.406,2.573 5.719,2.771 0.313,0.198 10 false *h 6.052,3.323 6.365,3.521 0.313,0.198 10 false *b 6.271,2.25 6.583,2.448 0.313,0.198 10 false *i 4.146,1.667 4.49,1.979 0.344,0.313 12 false *B 4.677,3.083 4.99,3.281 0.313,0.198 10 false *1
*A Pressing Forward *B Pulling
*1 Black Out Tape - -
*a Squeegee *b Release Paper
*c Sectional View *d Non-padded Side
*e Padded Side *f 3 to 7 cm/sec
*g 40 to 50° *h 30 to 45°
*i 10 to 20 mm - -


NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.


HINT:
·

Either angle of the squeegee (pressing forward or pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.





f.

Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)

i.
B147253C14
1.094,0.875 0.76,0.594 false 0.604,0.49 0.875,0.76 0.271,0.271 10 false *a 0.917,0.99 1.177,1.24 0.26,0.25 10 false *e 1.385,0.552 1.635,0.833 0.25,0.281 10 false *d 1.542,1.802 1.802,2.052 0.26,0.25 10 false *b 2.042,0.521 2.385,0.781 0.344,0.26 10 false *c
*a Squeegee
*b Hem
*c First
*d Second
*e Third


If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for installation of the tape (how to use a squeegee and installation procedure for corners)

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using an infrared light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.



h.

Check after installation

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

NOTICE:

Do not reuse the tape.




Hide 75922M 2.INSTALL NO. 1 BLACK OUT TAPE

a.

Clean the attachment surface (using an infrared light).

i.

Using an infrared light, heat any No. 1 black out tape and adhesive remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the remaining No. 1 black out tape and adhesive off the vehicle body.


iii.

Using a non-residue solvent, clean the attachment surface.



b.

Clean the attachment surface (using a tape removal disc).

i.

Set the 8 discs in the holder and insert the removal disc into an air drill or electric drill.

NOTICE:

Use an electric drill of which the no-load operation is 2000 to 3000 rpm.



ii.

Using a tape removal disc, rub the remaining No. 1 black out tape and adhesive off the vehicle body.

NOTICE:
·

Wear protective glasses during the operation.

·

Rotate and operate the disc in the correct direction.

·

Visually check that the cutting portion is not damaged while rubbing the remaining black out tape and adhesive off the vehicle body.




iii.

Using a non-residue solvent, clean the attachment surface.



c.

Apply new No. 1 black out tape to the positions shown in the illustration.

B348880E01
1.281,1.25 1.438,1.448 0.156,0.198 10 false A 1.427,1.719 1.583,1.917 0.156,0.198 10 false A 3.823,1.729 4.26,1.99 0.438,0.26 10 false A - A 4.583,1.885 4.74,2.083 0.156,0.198 10 false a 4.354,2.542 4.51,2.74 0.156,0.198 10 false b

Standard Measurement
Dimension Measurement
a 2.0 to 4.0 mm (0.0787 to 0.157 in.)
b 4.0 to 6.0 mm (0.158 to 0.236 in.)


d.

Remove the release paper and apply the No. 1 black out tape.


Hide 68151D 3.INSTALL FRONT DOOR GLASS RUN

Hide 75922M 4.INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING