Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
87150B
1.INSTALL HEATER RADIATOR ASSEMBLY
Install the heater radiator assembly.
Engage the claw and install the plate cover.
Install the 2 claws.
for RHD:
Engage the 2 claws and 3 guides and install the heater cover.
Install the 5 screws.
88625
2.INSTALL NO. 1 COOLER THERMISTOR
88501
3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
If a new No. 1 cooler evaporator sub-assembly is installed, add compressor oil to the No. 1 cooler evaporator sub-assembly as follows.
Add 40 cc (1.35 fl. oz.)
ND-OIL 8 or equivalent.
Install the No. 1 cooler evaporator sub-assembly with the No. 1 cooler thermistor.
for LHD:
Engage the 7 claws and install the lower heater case.
for RHD:
Engage the 8 claws and install the lower heater case.
Install the 6 screws.
Engage the clamp.
88515
4.INSTALL NO. 1 EXPANSION VALVE
Apply sufficient compressor oil to 2 new O-rings and fitting surfaces of a No. 1 expansion valve.
ND-OIL 8 or equivalent
| *1 | No. 1 Cooler Evaporator Sub-assembly |
Install the 2 O-rings onto the No. 1 cooler evaporator sub-assembly.
Using a 4 mm hexagon wrench, install the No. 1 expansion valve with the 2 hexagon bolts.
82210K
5.INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for Automatic Air Conditioning System)
for LHD:
Engage the 5 guides and install the air conditioning harness assembly.
for RHD:
Engage the 5 guides and install the air conditioning harness assembly.
88897U
6.INSTALL ASPIRATOR PIPE (for Automatic Air Conditioning System)
Engage the 2 claws and install the aspirator pipe.
88669E
7.INSTALL AIR HOSE (for Automatic Air Conditioning System)
Install the air hose.
87106H
8.INSTALL AIR MIX DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)
| *a | Reference position |
Align the reference position, and then install the air mix damper servo sub-assembly with the 3 screws.
Connect the connector.
87106J
9.INSTALL MODE DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)
| *a | Reference position |
Align the reference position, and then install the mode damper servo sub-assembly with the 3 screws.
Connect the connector.
87106N
10.INSTALL RECIRCULATION DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)
| *a | Reference position |
Align the reference position, and then install the recirculation damper servo sub-assembly with the 3 screws.
Connect the connector.
87106N
11.INSTALL RECIRCULATION DAMPER SERVO SUB-ASSEMBLY (for Manual Air Conditioning System)
88539
12.INSTALL NO. 1 COOLER UNIT DRAIN HOSE
Install the No. 1 cooler unit drain hose.
87139D
13.INSTALL AIR REFINER ELEMENT
Install the air refiner element.
Install the air refiner element with its UP marks oriented in the correct direction.
88548B
14.INSTALL AIR FILTER CASE
Engage the claw and guide to install the air filter case.
Install the air filter case with its UP mark oriented in the correct direction.
87103B
15.INSTALL BLOWER MOTOR WITH FAN SUB-ASSEMBLY
Install the blower motor with fan sub-assembly with the 3 screws.