After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch off before inspecting CAN bus lines for a ground short.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 23 CAN JUNCTION CONNECTOR
Check the No. 23 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 23 CAN Junction Connector) |
*b | to Brake Actuator Assembly |
| *c | to Combination Meter Assembly | *d | to No. 1 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 23 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| A60-5 (CANH) | L | Brake actuator assembly |
| A60-16 (CANL) | W | |
| F174-5 (CANH) | G | Combination meter assembly |
| F174-16 (CANL) | W | |
| F174-6 (CANH) | L | No. 1 CAN junction connector |
| F174-17 (CANL) | W |
NO. 1 CAN JUNCTION CONNECTOR
Check the No. 1 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to DLC3 |
| *c | to No. 23 CAN Junction Connector | *d | to ECM |
| *e | to Airbag ECU Assembly | *f | to Certification ECU (Smart Key ECU Assembly)*1 |
| *g | to Air Conditioning Amplifier Assembly | *h | to Steering sensor*2 |
| *i | to Power Steering ECU Assembly | - | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F62-1 (CANH) | GR | DLC3 |
| F62-12 (CANL) | W | |
| F62-2 (CANH) | L | No. 23 CAN junction connector |
| F62-13 (CANL) | W | |
| F62-3 (CANH) | BE | ECM |
| F62-14 (CANL) | W | |
| F62-4 (CANH) | B | Airbag ECU assembly |
| F62-15 (CANL) | W | |
| F62-7 (CANH) | L | Certification ECU (smart key ECU assembly)*1 |
| F62-18 (CANL) | W | |
| F62-8 (CANH) | V | Air Conditioning Amplifier Assembly |
| F62-19 (CANL) | W | |
| F62-9 (CANH) | R | Steering sensor*2 |
| F62-20 (CANL) | W | |
| F62-10 (CANH) | B | Power steering ECU assembly |
| F62-21 (CANL) | W |
*1: w/ Smart Entry and Start System
*2: w/ VSC
DLC3
Disconnect the cable from the negative (-) battery terminal.
| *1 | DLC3 | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F16-6 (CANH) - F16-14 (CANL) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F16-6 (CANH) - F16-4 (CG) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F16-14 (CANL) - F16-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F16-6 (CANH) - F16-16 (BAT) | GR - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F16-14 (CANL) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM
| *A | for CVT | *B | for Manual Transaxle |
| *a | Component without harness connected
(ECM) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connectors.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F130-13 (CANH) - F130-14 (CANL) | BE - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F130-13 (CANH) - B46-3 (E1) | BE - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F130-14 (CANL) - B46-3 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F130-13 (CANH) - F131-3 (BATT) | BE - G | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F130-14 (CANL) - F131-3 (BATT) | W - G | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (w/o VSC for LHD and CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A47-25 (CANH) - A47-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A47-25 (CANH) - A47-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A47-14 (CANL) - A47-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A47-25 (CANH) - A47-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A47-14 (CANL) - A47-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (w/o VSC except LHD and CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A35-25 (CANH) - A35-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A35-25 (CANH) - A35-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A35-14 (CANL) - A35-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A35-25 (CANH) - A35-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A35-14 (CANL) - A35-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (w/ VSC for LHD and CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A49-25 (CANH) - A49-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A49-25 (CANH) - A49-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-14 (CANL) - A49-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-25 (CANH) - A49-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A49-14 (CANL) - A49-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (w/ VSC except LHD and CVT)
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A48-25 (CANH) - A48-14 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A48-25 (CANH) - A48-1 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A48-14 (CANL) - A48-1 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A48-25 (CANH) - A48-12 (+BS) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A48-14 (CANL) - A48-12 (+BS) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG ECU ASSEMBLY (w/ Curtain Shield Airbag Assembly)
| *a | Component without harness connected
(Airbag ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the airbag ECU assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F21-13 (CANH) - F21-22 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F21-13 (CANH) - F21-25 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-22 (CANL) - F21-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-13 (CANH) - F16-16 (BAT) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F21-22 (CANL) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG ECU ASSEMBLY (w/o Curtain Shield Airbag Assembly)
| *a | Component without harness connected
(Airbag ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the airbag ECU assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F21-13 (CANH) - F21-22 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F21-13 (CANH) - F21-25 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-22 (CANL) - F21-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F21-13 (CANH) - F16-16 (BAT) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F21-22 (CANL) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)
| *a | Component without harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the certification ECU (smart key ECU assembly) connectors.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F44-40 (CANH) - F44-18 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F44-40 (CANH) - F43-10 (E) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F44-18 (CANL) - F43-10 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F44-40 (CANH) - F43-1 (+B) | L - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F44-18 (CANL) - F43-1 (+B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
| *a | Component without harness connected
(Combination Meter Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connecter
(to Combination Meter Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F38-23 (CANH) - F38-22 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| F38-23 (CANH) - F38-21 (EP) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F38-22 (CANL) - F38-21 (EP) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F38-23 (CANH) - F38-1 (B) | G - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F38-22 (CANL) - F38-1 (B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F3-11 (TX+) - F3-12 (TX-) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F3-11 (TX+) - F3-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F3-12 (TX-) - F3-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F3-11 (TX+) - F3-21 (B) | V - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F3-12 (TX-) - F3-21 (B) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the air conditioning amplifier connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F124-11 (TX+) - F124-12 (TX-) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F124-11 (TX+) - F124-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F124-12 (TX-) - F124-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F124-11 (TX+) - F16-16 (BAT) | V - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F124-12 (TX-) - F16-16 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEERING SENSOR (w/ VSC)
| *a | Component without harness connected
(Steering Sensor) |
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Disconnect the steering sensor connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F147-3 (CANH) - F147-2 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F147-3 (CANH) - F147-1 (ESS) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F147-2 (CANL) - F147-1 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F147-3 (CANH) - F147-5 (BAT) | R - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F147-2 (CANL) - F147-5 (BAT) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY
| *a | Component without harness connected
(Power Steering ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
Disconnect the power steering ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F12-7 (CANH) - F12-8 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| F12-7 (CANH) - F11-2 (PGND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F12-8 (CANL) - F11-2 (PGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| F12-7 (CANH) - F11-1 (PIG) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F12-8 (CANL) - F11-1 (PIG) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |