Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2018.01
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Steering sensor branch line or connector

·

Power source circuit of steering sensor

·

Steering sensor ground circuit

·

Steering sensor



WIRING DIAGRAM

E340805E11
3.667,1.188 4.167,0.188 4.167,0.188 4.333,0.188 false 4.75,1.188 4.917,0.75 4.917,0.75 5.083,0.75 false 0.094,0.083 1.01,0.281 0.917,0.198 10 false V Bus: 2.083,0.438 2.698,0.635 0.615,0.198 10 false DLC3 4.396,0.115 4.854,0.313 0.458,0.198 10 false F62 4.396,0.281 6.625,0.594 2.229,0.313 10 false No. 1 CAN Junction Connector 5.156,0.677 5.615,0.875 0.458,0.198 10 false F174 5.156,0.844 7.156,1.208 2,0.365 10 false No. 23 CAN Junction Connector 0.75,2.115 1.521,2.313 0.771,0.198 10 false 120 Ω 6.104,2.115 6.875,2.313 0.771,0.198 10 false 120 Ω 0.781,2.74 2.115,2.979 1.333,0.24 10 false F130 0.771,2.938 1.385,3.135 0.615,0.198 10 false ECM 5.708,2.74 6.167,2.938 0.458,0.198 10 false F38 5.708,2.906 6.927,3.385 1.219,0.479 10 false Combination Meter Assembly 0.229,4.333 1.604,5.125 1.375,0.792 10 false from Ignition or Starter Switch Assembly*1 or IG1 Relay*2 0.708,3.781 2.542,3.979 1.833,0.198 10 false from Battery 2.063,3.927 3.896,4.125 1.833,0.198 10 false DOME 1.927,4.469 3.76,4.667 1.833,0.198 10 false IG1 NO. 2 2.594,3.677 2.75,3.875 0.156,0.198 10 false 5 2.594,4.219 2.75,4.417 0.156,0.198 10 false 4 2.823,3.781 4.656,3.979 1.833,0.198 10 false BAT 2.802,4.313 4.635,4.51 1.833,0.198 10 false IG1 3.042,3.271 3.198,3.469 0.156,0.198 10 false 3 3.583,3.271 3.74,3.469 0.156,0.198 10 false 2 3.531,3.49 4.906,3.688 1.375,0.198 10 false CANL 3,3.49 4.375,3.688 1.375,0.198 10 false CANH 3.813,3.958 4.271,4.156 0.458,0.198 10 false ESS 4.24,3.844 4.396,4.042 0.156,0.198 10 false 1 2.688,4.635 3.302,4.833 0.615,0.198 10 false F147 2.677,4.802 4.583,5.021 1.906,0.219 10 false Steering Sensor 4.792,4.375 6.625,4.573 1.833,0.198 10 false Trouble Area 1.167,5.958 5.146,6.156 3.979,0.198 10 false : CAN Main Bus Line (CANH) 4.323,5.958 6.813,6.229 2.49,0.271 10 false : CAN Branch Bus Line (CANH) 4.313,6.365 6.802,6.635 2.49,0.271 10 false : CAN Branch Line (CANL) 1.156,6.365 5.135,6.563 3.979,0.198 10 false : CAN Main Bus Line (CANL) 0.24,5.563 2.625,5.979 2.385,0.417 10 false *1: w/o Smart Entry and Start System 2.865,5.552 5.208,5.896 2.344,0.344 10 false *2: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.74 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (STEERING SENSOR BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C277459C42
1.49,0.229 1.885,0.479 0.396,0.25 1.323,1.875 1.51,1.385 true 2.031,1.865 1.719,1.385 true 1.531,0.271 2.146,0.469 0.615,0.198 10 false F147 1.958,1.885 2.5,2.083 0.542,0.198 10 false CANH 1.177,1.906 1.719,2.104 0.542,0.198 10 false CANL 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F147-3 (CANH) - F147-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (STEERING SENSOR)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C277459C43
1.49,0.229 1.885,0.479 0.396,0.25 1.01,1.802 1.323,1.354 true 2.167,1.854 1.896,1.365 true 2.542,1.781 2.094,1.365 true 1.531,0.271 2.146,0.469 0.615,0.198 10 false F147 2.552,1.802 3.083,2.01 0.531,0.208 10 false BAT 2.104,1.885 2.646,2.083 0.542,0.198 10 false IG1 0.802,1.813 1.344,2.01 0.542,0.198 10 false ESS 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F147-1 (ESS) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F147-4 (IG1) - Body ground Ignition switch ON 11 to 14 V
F147-5 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)