When the engine is running or the ignition switch is ON, the front power window regulator motor assembly (driver side) is operated by the power window regulator master switch assembly. The front power window regulator motor assembly (driver side) has motor, regulator and ECU functions.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When the front power window regulator motor assembly (driver side) is reinstalled or replaced, the power window control system must be initialized.
Replacing the door glass or door glass run may cause a difference to exist between the current door glass position and the position memorized in the ECU. In this case, the jam protection function may work improperly. Return the system to the pre-initialized condition and reinitialize the system.
Disconnect the power window regulator motor connector during power window operation. This will return the motor to the pre-initialized condition.
The auto up function will not work unless initialization is completed.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Remove the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION
Inspect the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
| *a | Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly) |
Disconnect the power window regulator master switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H8-7 (B) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H8-1 (E) - Body ground | Always | Below 1 Ω |
for RHD
| *a | Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly) |
Disconnect the power window regulator master switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G5-7 (B) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G5-9 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
| *a | Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH) |
Disconnect the front power window regulator motor assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H11-2 (B) - Body ground | Always | 11 to 14 V |
| H11-6 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H11-1 (GND) - Body ground | Always | Below 1Ω |
Reconnect the front power window regulator motor assembly LH connector.
for RHD
| *a | Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly RH) |
Disconnect the front power window regulator motor assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G11-2 (B) - Body ground | Always | 11 to 14 V |
| G11-6 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G11-1 (GND) - Body ground | Always | Below 1Ω |
Reconnect the front power window regulator motor assembly RH connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the H8 power window regulator master switch assembly connector.
Disconnect the H11 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H8-6 (U) - H11-10 (UP) | Always | Below 1Ω |
| H8-3 (D) - H11-7 (DOWN) | Always | Below 1Ω |
| H8-4 (A) - H11-4 (AUTO) | Always | Below 1Ω |
| H8-6 (U) or H11-10 (UP) - Body ground | Always | 10 kΩ or higher |
| H8-3 (D) or H11-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| H8-4 (A) or H11-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
Reconnect the H8 power window regulator master switch assembly connector.
Reconnect the H11 front power window regulator motor assembly LH connector.
for RHD
Disconnect the G5 power window regulator master switch assembly connector.
Disconnect the G11 front power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G5-3 (U) - G11-10 (UP) | Always | Below 1Ω |
| G5-6 (D) - G11-7 (DOWN) | Always | Below 1Ω |
| G5-4 (A) - G11-4 (AUTO) | Always | Below 1Ω |
| G5-3 (U) or G11-10 (UP) - Body ground | Always | 10 kΩ or higher |
| G5-6 (D) or G11-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| G5-4 (A) or G11-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
Reconnect the G5 power window regulator master switch assembly connector.
Reconnect the G11 front power window regulator motor assembly RH connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG