Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › from 2018.01
RM30M0E _59 Vehicle Exterior _017123 MIRROR (EXT) _0087435 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retract Mirror)

a.
B488370C01
2.333,1.146 2.75,0.729 true 0.51,1 0.927,1.417 true 0.281,3.01 0.698,3.427 true 2.542,3.75 2.958,4.167 true 0.99,3.427 1.406,3.01 true 2.5,3.417 2.917,3 true 0.448,4.167 0.865,3.75 true 0.885,4.167 1.302,3.75 true 2.156,3.75 2.573,4.167 true 1.917,3.75 2.167,4.167 true 1.25,4.167 1.5,3.75 true 1.708,3.75 1.792,4.167 true 2.75,3.5 3.167,3.667 true 0.323,0.896 0.635,1.052 0.313,0.156 10 false *1 2.823,0.625 3.135,0.781 0.313,0.156 10 false *2 0.094,2.646 0.406,2.802 0.313,0.156 10 false *a 0.052,2.896 0.365,3.094 0.313,0.198 10 false E2 1.479,2.896 1.792,3.094 0.313,0.198 10 false MF 2.99,2.896 3.333,3.083 0.344,0.188 10 false ACC 3.083,3.688 3.344,3.875 0.26,0.188 10 false MR 2.927,4.188 3.188,4.375 0.26,0.188 10 false B 2.521,4.188 2.781,4.375 0.26,0.188 10 false HL 2.104,4.188 2.365,4.375 0.26,0.188 10 false VL 1.708,4.188 1.969,4.375 0.26,0.188 10 false HR 1.146,4.188 1.406,4.375 0.26,0.188 10 false VR 0.76,4.188 1.021,4.375 0.26,0.188 10 false M+ 0.385,4.188 0.646,4.375 0.26,0.188 10 false E
*1 Mirror Retract Switch
*2 Mirror Select Switch and Mirror Surface Adjust Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (MF) - 2 (ACC) Extended position Below 1 Ω
1 (MR) - 5 (E2)
4 (MF) - 5 (E2) Retracted position Below 1 Ω
1 (MR) - 2 (ACC)


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
10 (VL) - 7 (B)
13 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
10 (VL) - 15 (E)
13 (M+) - 7 (B)
Down Below 1 Ω
Off 10 kΩ or higher
9 (HL) - 7 (B)
13 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
9 (HL) - 15 (E)
13 (M+) - 7 (B)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
12 (VR) - 7 (B)
13 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
12 (VR) - 15 (E)
13 (M+) - 7 (B)
Down Below 1 Ω
Off 10 kΩ or higher
11 (HR) - 7 (B)
13 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
11 (HR) - 15 (E)
13 (M+) - 7 (B)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.
B488370C02
0.781,4.25 1.115,3.75 true 2.354,3.75 2.688,4.25 true 0.198,2.583 0.51,2.74 0.313,0.156 10 false *a 0.667,4.26 1.063,4.427 0.396,0.167 10 false ILL- 2.583,4.26 2.979,4.427 0.396,0.167 10 false ILL+
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the switch illumination.

i.

Apply battery voltage between the terminals of the light and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 8 (ILL+)
Battery negative (-) → Terminal 14 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retract Mirror)

a.
B379396C01
2.302,1.146 3.021,0.729 true 0.906,3.771 0.531,4.188 true 1.313,3.771 0.896,4.188 true 1.51,3.771 1.313,4.188 true 1.708,3.771 1.75,4.198 true 1.917,3.771 2.146,4.198 true 2.146,3.771 2.531,4.198 true 2.542,3.771 2.885,4.198 true 3.052,0.604 3.24,0.76 0.188,0.156 10 false *1 0.229,2.76 0.417,2.917 0.188,0.156 10 false *a 0.458,4.219 0.573,4.375 0.115,0.156 10 false E 0.76,4.219 0.979,4.375 0.219,0.156 10 false M+ 1.188,4.219 1.417,4.375 0.229,0.156 10 false VR 1.625,4.219 1.854,4.375 0.229,0.156 10 false HR 2.063,4.219 2.26,4.375 0.198,0.156 10 false VL 2.469,4.219 2.667,4.375 0.198,0.156 10 false HL 2.865,4.219 2.979,4.375 0.115,0.156 10 false B
*1 Mirror Select Switch and Mirror Surface Adjust Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror select switch and mirror adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
7 (B) - 10 (VL)
13 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
7 (B) - 13 (M+)
10 (VL) - 15 (E)
Down Below 1 Ω
Off 10 kΩ or higher
7 (B) - 9 (HL)
13 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
7 (B) - 13 (M+)
9 (HL) - 15 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
7 (B) - 12 (VR)
13 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
7 (B) - 13 (M+)
12 (VR) - 15 (E)
Down Below 1 Ω
Off 10 kΩ or higher
7 (B) - 11 (HR)
13 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
7 (B) - 13 (M+)
11 (HR) - 15 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.
B379396C02
0.854,4.25 1.104,3.75 true 2.354,3.75 2.604,4.25 true 0.396,2.75 0.708,2.906 0.313,0.156 10 false *a 0.75,4.26 1.146,4.427 0.396,0.167 10 false ILL- 2.521,4.26 2.917,4.427 0.396,0.167 10 false ILL+
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the switch illumination.

i.

Apply battery voltage between the terminals of the light and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 8 (ILL+)
Battery negative (-) → Terminal 14 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.