Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › from 2018.01
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0346761 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69340 1.INSPECT REAR DOOR LOCK ASSEMBLY LH

a.
B343711C01
0.771,3.75 1.188,3.75 true 0.75,3.75 1.167,3.75 true 2.094,3.75 2.51,3.75 true 0.896,3.042 1.208,3.198 0.313,0.156 10 false *a 1.771,2.698 2.083,2.854 0.313,0.156 10 false *b 1.104,2.698 1.417,2.854 0.313,0.156 10 false *c 2.542,3.656 2.917,3.917 0.375,0.26 10 false UL 0.615,3.656 0.99,3.917 0.375,0.26 10 false L
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Unlock
*c Lock


Check the operation.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locked
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocked


If the result is not as specified, replace the rear door lock assembly LH.



b.
B343711C03
1.26,4.417 1.354,4.042 true 1.885,4.052 1.979,4.385 true 0.896,3.042 1.208,3.198 0.313,0.156 10 false *a 1.771,2.698 2.083,2.854 0.313,0.156 10 false *b 1.104,2.698 1.417,2.854 0.313,0.156 10 false *c 1.823,4.417 2.323,4.635 0.5,0.219 10 false LSSR 1.188,4.427 1.552,4.635 0.365,0.208 10 false E
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Unlock
*c Lock


Check the resistance of the unlock detection switch.

(w/ Unlock Detection Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock assembly LH.



Hide 69330 2.INSPECT REAR DOOR LOCK ASSEMBLY RH

a.
B343712C01
0.76,3.719 1.177,3.719 true 2.104,3.719 2.521,3.719 true 0.854,3 1.167,3.156 0.313,0.156 10 false *a 1.521,2.677 1.833,2.833 0.313,0.156 10 false *b 2.25,2.667 2.563,2.823 0.313,0.156 10 false *c 0.625,3.615 0.938,3.771 0.313,0.156 10 false L 2.583,3.625 2.896,3.781 0.313,0.156 10 false UL
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Unlock
*c Lock


Check the operation.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locked
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocked


If the result is not as specified, replace the rear door lock assembly RH.



b.
B343712C04
1.25,4.375 1.354,4.042 true 1.896,4.042 1.979,4.385 true 0.854,3 1.167,3.156 0.313,0.156 10 false *a 1.521,2.677 1.833,2.833 0.313,0.156 10 false *b 2.25,2.667 2.563,2.823 0.313,0.156 10 false *c 1.177,4.396 1.49,4.552 0.313,0.156 10 false E 1.823,4.396 2.333,4.573 0.51,0.177 10 false LSSR
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Unlock
*c Lock


Check the resistance of the unlock detection switch.

(w/ Unlock Detection Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock assembly RH.