Home › Brake › BRAKE (REAR) › REAR BRAKE(for Disc Type) › from 2018.01
RM30M0E _54 Brake _017101 BRAKE (REAR) _0092768 REAR BRAKE(for Disc Type) A

BRAKE (REAR)  REAR BRAKE(for Disc Type)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 58910C 3.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 4.LOOSEN PARKING BRAKE CABLE

a.
C282403C03
1.083,1.656 1.729,1.281 true 0.938,1.583 1.135,1.781 0.198,0.198 10 false *1
*1 Lock Nut


Loosen the lock nut and equalizer.

NOTICE:

If the lock nut has been removed from the rod, replace the lock nut with a new one.



Hide 46430 5.DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C282418

Disconnect the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.


b.
C282419C01
2.417,1.396 2.635,1.5 false 2.823,1.271 2.99,1.271 false 3.021,1.167 3.333,1.323 0.313,0.156 10 false *1 2.26,1.292 2.573,1.448 0.313,0.156 10 false *a
*1 No. 3 Parking Brake Cable Assembly
*a Clip


Insert a 14 mm offset wrench at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip, and separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.


Hide 47319F 6.DISCONNECT REAR FLEXIBLE HOSE

a.
C294091

Remove the union bolt and gasket, to disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 47850 7.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C282421C01
0.531,0.917 0.844,1.073 0.313,0.156 10 false *a 1.427,0.073 1.74,0.229 0.313,0.156 10 false *b
*a Hold
*b Turn


Hold each rear disc brake pad guide pin and remove the 2 bolts and rear disc brake cylinder assembly from the rear disc brake cylinder mounting.


Hide 04466 8.REMOVE REAR DISC BRAKE PAD

a.
C282422

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 9.REMOVE REAR DISC BRAKE ANTI SQUEAL SHIM KIT

a.
C275019C02
0.417,1.313 0.417,1.042 false 0.896,1.604 0.896,1.333 false 2.5,2.49 2.5,2.219 false 2.917,2.76 2.917,2.49 false 1.917,2.271 1.917,2 false 1.333,2 1.333,1.729 false 2.427,2.521 2.74,2.677 0.313,0.156 10 false *1 0.354,1.354 0.667,1.51 0.313,0.156 10 false *2 0.833,1.635 1.146,1.792 0.313,0.156 10 false *1 2.844,2.802 3.156,2.958 0.313,0.156 10 false *2 1.854,2.302 2.167,2.458 0.313,0.156 10 false *3 1.271,2.01 1.583,2.167 0.313,0.156 10 false *3
*1 Rear No. 1 Disc Brake Anti Squeal Shim
*2 Rear No. 2 Disc Brake Anti Squeal Shim
*3 Rear Disc Brake Pad


Remove the rear No. 1 disc brake anti squeal shim and rear No. 2 disc brake anti squeal shim from each rear disc brake pad.


Hide 04948 10.REMOVE REAR DISC BRAKE FITTING KIT

a.
C282423C01
0.24,0.573 0.667,0.573 false 0.24,1.385 0.469,1.385 false 0.073,1.292 0.385,1.448 0.313,0.156 10 false *1 0.073,0.469 0.385,0.625 0.313,0.156 10 false *2
*1 Rear No. 1 Disc Brake Pad Support Plate
*2 Rear No. 2 Disc Brake Pad Support Plate


Remove the rear No. 1 disc brake pad support plate and rear No. 2 disc brake pad support plate from the rear disc brake cylinder mounting.

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 47835 11.REMOVE REAR DISC BRAKE PAD GUIDE PIN

a.
C282424

Remove the 2 rear disc brake pad guide pins from the rear disc brake cylinder mounting.


b.
C294084C02
2.417,1.51 2.792,1.021 false 2.854,0.938 3.167,1.094 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the rear disc brake cylinder slide bush from each rear disc brake pad guide pin.

NOTICE:

Do not damage the rear disc brake pad guide pin.



Hide 47875R 12.REMOVE REAR DISC BRAKE BUSH DUST BOOT

a.
C282425

Remove the 2 rear disc brake bush dust boots from the rear disc brake cylinder mounting.


Hide 47822 13.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C282426

Remove the 2 bolts and rear disc brake cylinder mounting from the rear axle beam assembly.


Hide 42431 14.REMOVE REAR DISC

a.
C283238C01
1.927,0.906 2.906,0.792 2.906,0.792 1.958,0.969 true 2.938,0.698 3.25,0.854 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear disc and rear axle hub and bearing assembly.


b.

Remove the rear disc.