Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C197053C23
0.139,0.087 0.410,0.276 0.272,0.188 10 *a
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))


Terminal No. (Symbol) Terminal Description
1 (GND1) Skid control ECU ground
2 (STP) Stop light switch input
4 (RL-) Rear wheel speed LH (-) signal input
5 (RL+) Rear wheel speed LH (+) power supply output
6 (FR-) Front wheel speed RH (-) signal input
7 (FR+) Front wheel speed RH (+) power supply output
11 (SP1) Speed signal output for speedometer
12 (+BS) Solenoid relay power supply
13 (GND2) Pump motor ground
14 (CANL) CAN communication line L
16 (RR-) Rear wheel speed RH (-) signal input
17 (RR+) Rear wheel speed RH (+) power supply output
18 (FL-) Front wheel speed LH (-) signal input
19 (FL+) Front wheel speed LH (+) power supply output
24 (BM) Motor relay power supply
25 (CANH) CAN communication line H
27 (EXI3)* Back-up light switch assembly input
30 (CSW) VSC OFF switch input
34 (IG1) ECU power supply

*: for Manual Transaxle



TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage or resistance on the wire harness side.

C349102C05
1.833,0.083 2.333,0.333 0.5,0.25 4.802,0.083 5.302,0.333 0.5,0.25 0.75,0.167 1.125,0.385 0.375,0.219 12 false *A 3.698,0.167 4.156,0.469 0.458,0.302 12 false *B 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.958,0.115 2.417,0.313 0.458,0.198 10 false A48 4.917,0.125 5.375,0.323 0.458,0.198 10 false A49
*A except LHD with Continuously Variable Transaxle *B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -


HINT:

Voltage cannot be measured with the connector connected to the brake actuator assembly (skid control ECU) as the connector is watertight.


Standard:
except LHD with Continuously Variable Transaxle
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*: for Manual Transaxle

A48-1 (GND1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω
A48-2 (STP) - Body ground SB - Body ground Stop light switch input Stop light switch ON → OFF
(Brake pedal depressed → released)
7.5 to 14 V → Below 1.5 V
A48-12 (+BS) - Body ground W - Body ground Solenoid relay power supply Always 11 to 14 V
A48-13 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A48-24 (BM) - Body ground B - Body ground Motor relay power supply Always 11 to 14 V
A48-25 (CANH) - A48-14(CANL) L - W CAN bus Ignition switch off 54 to 69 Ω
A48-30 (CSW) - Body ground P - Body ground VSC OFF switch input VSC OFF switch held ON → OFF (Not pressed) Below 25 Ω → 10 kΩ or higher
A48-34 (IG1) - Body ground L - Body ground ECU power supply Ignition switch ON 11 to 14 V
A48-27 (EXI3)* - Body ground GR - Body ground Back-up light switch assembly input Shift lever not in R → Shift lever in R Below 1.5 V → 7.5 to 14 V

for LHD with Continuously Variable Transaxle
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A49-1 (GND1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω
A49-2 (STP) - Body ground SB - Body ground Stop light switch input Stop light switch ON → OFF
(Brake pedal depressed → released)
7.5 to 14 V → Below 1.5 V
A49-12 (+BS) - Body ground W - Body ground Solenoid relay power supply Always 11 to 14 V
A49-13 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A49-24 (BM) - Body ground B - Body ground Motor relay power supply Always 11 to 14 V
A49-25 (CANH) - A49-14 (CANL) L - W CAN bus Ignition switch off 54 to 69 Ω
A49-30 (CSW) - Body ground P - Body ground VSC OFF switch input VSC OFF switch held ON → OFF (Not pressed) Below 25 Ω → 10 kΩ or higher
A49-34 (IG1) - Body ground L - Body ground ECU power supply Ignition switch ON 11 to 14 V